1 / 6
Kellertür-Griff 03 / 8mm kt / "WINTITSCH" / Gebäude Bj. 1965 / Update 9.1.2023 jetzt auch f. 7 mm — zdjęcie 1
1 / 6

Kellertür-Griff 03 / 8mm kt / "WINTITSCH" / Gebäude Bj. 1965 / Update 9.1.2023 jetzt auch f. 7 mm

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Cellar door handle 03 / 8mm kt / "WINTITSCH" / building built in 1965 / Update 9.1.2023 now also for 7 mm

Ocena
0 / 5
Polubienia
13
Pobrania
65
Wydruki
0
Wyświetlenia
298
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

Kellertür-Griff 03   “WINTITSCH”

Passend für 8mm Vierkant.

Nicht nur in den 1960er Jahren wurden die Türgriffe an solchen meist Keller,  Dachboden oder Schuppen-Türen häufig aus Bakelit ( einem Phenoplast / Duroplast) hergestellt. (Bild 4 )

Eigentlich ein gutes und beständiges Material, ein Nachteil ist jedoch das es recht spröde ist und z.B. durch Schläge oder Herunterfallen brechen kann.

Mir ist ein solcher Griff leider zerbrochen so das ich einen neuen generiert habe um die Tür zu reparieren. Gebäude Bj. 1965

Update 9.1.2023:

Auf Anfrage von xijen habe ich noch eine Variante für 7mm 4kt beigefügt.

Als Material empfehle ich in folgender Reihenfolge.:

PC (Polycarbonat), PETG, ABS oder PLA

Als Füllgrad empfehle ich 100% (wenn die Mechanik sehr leichtgängig ist kann man auch etwas weniger füllen) bei Verwendung von PC (Polycarbonat) reicht auch ein Füllgrad von 50%.

Schichthöhe ca. 0,3mm (auch wenn feinere Schichten schöner aussehen, geht dies meist zu Lasten einer guten Verbindung der Schichten )

----------------------------------------------------------------------------------------

Google translates:

Cellar door handle 03 “WINTITSCH”

Suitable for 8mm square.

It was not only in the 1960s that the door handles on such mostly basement, attic or shed doors were often made of bakelite (a phenoplastic / thermoset). (Picture 4 )

Actually a good and durable material,
However, one disadvantage is that it is quite brittle and can break, e.g. due to hits or falling.

Unfortunately, one of these handles broke so I generated a new one to repair the door. Building built in 1965

Update 9.1.2023:

At the request of xijen I have added a variant for 7mm 4kt.

As material I recommend in the following order.:

PC (polycarbonate), PETG, ABS or PLA
I recommend 100% filling level (if the mechanism is very smooth-running, you can also fill a little less) when using PC (polycarbonate) a filling level of 50% is sufficient.

Layer height approx. 0.3mm (even if finer layers look nicer, this is usually at the expense of a good connection between the layers)

Tagi