Dungeon! Game Token and Card Holder Set
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
3,21 € – 3,93 € netto (bez VAT)
Dla pliku: Dungeon! - Spell Card Holder_4h8m_0.16mm_205C_PLA_ENDER3V2.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 3,57 € netto (środek widełek).
- Masa podana przez autora
- 33 g
- Czas druku podany przez autora
- 4,13 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Piece and card tray set for the Dungeon! Fantasy Board Game for use while playing and storing in the box.
- Ocena
- 5 / 5
- Polubienia
- 21
- Pobrania
- 117
- Wydruki
- 1
- Wyświetlenia
- 958
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Board Games
- Licencja
- Creative Commons — Attribution — Noncommercial
This is a complete set of organizers for all cards and components of Dungeon! the board game to keep your table tidy and allow you to focus on the game. Each tray has an optional lid that you can use to store everything in the respective trays and carry in the game box without worry of them falling out or becoming disorganized.
The box is so large that I couldn't think of a reasonable solution to keep the trays from moving around but they should be robust enough to handle some jostling without much issue. You can also set each tray inside the lid but it makes the cards more difficult to grab from the card tray (last picture). If you have any ideas for improvement or optimization I am always open to feedback.
Encounter Card Holder & Encounter Card Lid
You'll need two of these trays, and optionally lids, to hold the encounter and treasure cards for the six dungeon levels. Each level is intended to take up a single column with the top two “dragon” spots for the monster draw and discard piles and the bottom “chest” spot holding the level's treasure cards.
Print Details | |
|---|---|
| Layer Height | .20 mm |
| Infill | None |
| First Layer Note | I slowed my first layer down, for the tray only, to 60% for so the design in dragon and chests stayed adhered using a smooth PEI steel plate. |
| Filament | Overture Black PLA |
Spell Card Holder
Holds the cards for the wizard's spellbook.
Print Details | |
|---|---|
| Layer Height | .20 mm |
| Infill | None |
| First Layer Note | I slowed my first layer down to 60% for so the design in the tray stayed adhered using a smooth PEI steel plate. |
| Filament | eSUN Pro Green (Pantone 323C) PLA |
Figure and Dice Holder
The small area is for the two dice and the larger area fits the eight hero standees.
Print Details | |
|---|---|
| Layer Height | .20 mm |
| Infill | None |
| First Layer Note | I slowed my first layer down to 60% for so the grid in the lid stayed adhered using a smooth PEI steel plate. |
| Filament | Creality Matte Blue PLA |
Token Holder
Individual compartments hold each of the 12 Number tokens, Lose a Turn tokens, Magic Sword tokens, and Defeated tokens. The 12 Number tokens sit in a row on the top. The Lose a Turn tokens fit in the two compartments on the middle-left. The Magic Sword tokens take the middle-right. Finally, the large bottom compartment holds the Defeated tombstone tokens.
The lid fits on the tray two different ways but you'll want the divider bar along the top separating the Defeated tombstone tokens into the larger compartment. The other tokens should stay put either way so it shouldn't be too big of a problem if it's not put on as intended.
Print Details | |
|---|---|
| Layer Height | .20 mm |
| Infill | 5% Gyroid |
| Color Change | The text and symbols on the trays are raised to allow for a color change of the top three layers. You can also paint the raised symbols instead. |
| Filament | Base: Hatchbox Light Purple PLA Text/Symbols: Overture White PLA |
Artwork Attribution
The artwork used in the design is credited to the creators listed below from the Noun Project.
- dragon by Icons Producer
- treasure by Adrien Coquet
- chevron by Nikita Kozin
- person by Mello
- Fire by Alina Oleynik
- explosion by Abdul Wahhab
- Lightning Bolt by richard pasqua
- Tombstone by David Khai
- magic sword by lastspark
- hourglass by Vectors Market