1 / 16
Another K40 adjustable bed — zdjęcie 1
1 / 16

Another K40 adjustable bed

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An optimized adjustable bed for laser machines

Ocena
5 / 5
Polubienia
25
Pobrania
122
Wydruki
2
Wyświetlenia
1374
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

Yet another adjustable table for your K40 laser cutter from the finest material the world has ever seen: Chinesium!

This adjustable bed is inspired by the table made by arion02 on Thingiverse (https://www.thingiverse.com/thing:2299337)

I've performed some updates and tweaks on that:

  • Required hardware for the frame is a 15 mm x 15 mm square tube (See part list below) Much easier to get here in Europe than the imperial 12.7 mm (13 mm) variant.
  • Added a belt tensioner
  • The bearing is now in line with the tube, thus it's reducing bending moments when tightening the belt
  • Option to lock the tube in place with a M3 bolt (if you don't want to glue)
  • Option to mount the frame to the base (7 mm blind holes)
  • Option to fasten the top surface to the Top Corners (6 mm blind holes, plenty of alignment possibility with a M3 bolt + washer)

Part List (see Links, worked at least in December 2022)

4x M8 threaded rod (length depending on your application) [Amazon]
5x bearing 608 ZZ (D22xD8xH7) [Amazon]
4x 15 mm x 15 mm aluminum tubes (for the short side) (Don't use Amazon here since they are ridiculously expensive. Go to Ebay or your local hardware store)
4x 15 mm x 15 mm aluminum tubes (for the long side)

EDIT 12.01.2024:
For a bed of 340 mm x 230 mm you'll need 4x short tubes of 166 mm length and 4 long tubes of 276 mm length. For larger or smaller honeycomb beds edit the tubes accordingly.

4x GT2 pulleys for a 6 mm belt (I've cannibalized some from my Ultimaker)[Amazon]
1x GT2 timing belt 6 mm (for my configuration I've chosen 1140 mm length, see the step model) [Amazon]
10x M8 nut (yeah, no additional information in brackets! ;-) )
1x M8x25 bolt hex head (
2x M8 washers
Loctite (feels lonely w/o bracket text :-) )

Optionally:
Tube clamping
17 x M3x6 (any size higher than 5 mm will do)
17 x M3 nut (and some patience to install it into the pockets)

Bed clamping
4x M3 bolt, length depending on your bed material
4x M3 washer
4x M3 stop nut (it just looks so much cooler than regular nuts ;-) )

Bed material
Aluminum Honeycomb 340 mm x 230 mm [Ebay]. Almost everything will do as long it doesn't reflect the laser beam!

 

Instructions:

  1. Print all parts :-) See my print settings below, they worked well.
    (4x corner_Bottom, 4x Corner_Top, 1x Belt_Tensioner, 2x Spacer)
  2. Press the bearings into the Corner_Bottom pieces. It sould be a snug fit so use a vise or a M8 bolt, 2 M8 Washers and a nut to press the bearing in. Dont use a hammer in order not to damage the part!
  3. Press the M8 nuts into the Corner_Top parts. Again, it's a snug fit, use a vise or similar. Don't hammer the nuts in!
  4. Cut the M8 threaded rods to length.
  5. Take a deep breath and install the M3 nuts into the pockets behind the tube reception channels of top and bottom corner parts as well as the belt tensioner.
    You might need some patience but with help of a M3 bolt and a M3 washer you should get these into position. Did I mention you need sensitive hands and some patience?
  6. Use some beverage of your choice to celebrate the installation of the M3 nuts; that was the trickiest part of the whole assembly. Beer works here. Whisky as well. Choose a good Scotch. :-)
  7. Use a metal cut saw or an angle grinder to make a slot in one (or all) of one butt end of the threaded rods. You can use this slit later to change height of the bed with a slotted screwdriver
  8. Align each one M8 nut with one threaded rod and ensure nut and rod are flush (not the slotted end!). Secure with some Locktite (any glue would work I guess)
  9. Install the threaded rods into the bearings of the bottom corners from below
  10. Slide the pulleys over the threaded rods but DON'T secure them them with the set screw(s) yet
  11. Install all tubes of the lower frame (2x short, 2x long). Secure them with the short M3 screws. DON'T OVERTIGHTEN THEM! (German proverb says "Beyond tightened it becomes loose again")
  12. Use the M8x25 bolt, two washers and one bearing and form a belt tension wheel. Install the a spacer between M8 washers and bearing just that the bearing is rotating freely between the washers, see also the attached section view. Use a M8 nut so secure the sub-assembly loosely to the LOWER side (print bed side) of the belt tensioner part.
  13. Install the belt tensioner from above onto a long tube of the lower frame and secure the position with a M3 screw. The belt tension wheel is on the upper side of the belt tensioner part. See the STP file.
  14. Install the GT2 belt loosly onto the 4 pulleys and the belt tension wheel. Don't tighten the belt yet.
  15. Assemble the upper frame the same way as the lower frame and secure all tubing with M3 bolts
  16. Install the upper frame onto the threaded rods (the pressed-in nuts face downwards!) and lower the upper frame about half way down. Try to be as level as possible.
  17. Tighten the belt and secure the tightening wheel with the M8 nut. DON'T overtighten the belt, there's no need to let the belt sing! Just tighten it enough so each pulley will rotate the same speed when leveling the bed. The pulleys are still loose!
  18. Use a jig or distance piece to level the upper frame. That can be a bit tricky but a well-leveled bed pays off later in cutting and engraving quality!
  19. Ensure the upper frame is absolutely parallel to the lower frame, then push all pulleys downwards to the bearing and tighten the set screw(s) on the pulleys.
  20. Install the bed and optionally secure it with M3 bolts, washers and the beloved stop nuts :-)
  21. Optionally mount the lower frame to your base, if needed, use the Ø7 holes of the lower corner parts.
  22. Open the second bottle of your favorite beverage and enjoy your work. 
    You Made It
  23. Don't use the laser right not since you might be drunk already :-) Don't drink and drive your laser! :-)

Questions? Sure, why not!

Q: Can you make the corners for other tubing sizes?
A: Nope, sorry but the design of the parts is straight forward so feel free to copy and modify it. Alternatively use some shims to adapt it to smaller tube sizes.

Q: What height/width/length should I use for the frame/bed?
A: I already pre-digested most of the brainfood here, please try to figure it out based on your individual configuration.

Q: Does a brilliant mind as you are have other projects apart from creating such masterpieces of engineering excellence?
A: Thank you very much for the compliment, I'll share them when they are finished :-)

Enjoy and let me know your thoughts on the design!