1 / 8
Omnifixo Helping Hands Display and Travel Case. Gridfinity 4x2 — zdjęcie 1
1 / 8

Omnifixo Helping Hands Display and Travel Case. Gridfinity 4x2

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A dual purpose case for the best soldering helping hands tool, the Omnifixo. Uses Gridfinity System.

Ocena
5 / 5
Polubienia
62
Pobrania
171
Wydruki
3
Wyświetlenia
3662
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution

If you are unfamiliar with the Omnifixo, it is by far the best “helping hands” system I have used for soldering. https://omnifixo.com

I wanted to create an compact footprint Omnifixo case that was also compatible with Gridfinity. The problem is, while the width fit within 4x Gridfinity tiles, the height was slightly larger than 2x Gridfinity tiles. Instead of accepting a 4x3 Gridfinity solution I developed this case is a dual purpose display and travel case. (All pictures are the 8 unit tall STL)

The Omnifixo plate can be stowed vertically in the case in “presentation mode” which is inline with the spirit of Gridfinity. When you need to take your soldering tools on the go, you can then convert the plate to a lid for the box. 

The inside of the box is sparse, allowing maximum storage ability, but if you want some more organization there are STLs and STEP files that allow you to make interior organizers for the box in “display mode” and “travel mode”.

I have included my sample layout STLs, but it is catered to my specific tools, and is there purely for example.

You are also able to use 1x3 or smaller Gridfinity components in the front half of this case.

 

To this end, I look some inspiration from meffken's omnifixo case design and designed a 1x1 solder tip cleaner that can magnetically attach to the side of the travel case, as well as balance a soldering iron.

 

Parts

Following are rev share links. Thanks for your support.

The magnets used all all the pieces are 6mm x 2mm, same as Gridfinity system.
https://amzn.to/3V49HNl

The gold tip clean sponge are from this set, and a single sponge is cut into thirds: https://amzn.to/3uSnEU6

Pictured

the TS80P: https://amzn.to/3BFInOw I like it because it can be powered off of usbc, and how easy it is to swap out tips.

An open source alternative is the Pinecil: https://pine64.com/product-category/pinecil/

If you decide on either of these, you can use an open source firmware to control them: https://github.com/Ralim/IronOS It is nice, offers more customization of the UI and button functions. It also opens up the irons to use 5v usb power sources, just takes them longer to heat up. The minimal holder I am using for my TS80P can be found here. I really like how compact it is, while keeping all the tips together: https://www.thingiverse.com/thing:4373687

MHP30 usbc powered tiny electric hotplate: https://amzn.to/3FBlaON

Anker 30w USBC charger: https://amzn.to/3FYqkWn

Pokit multimeter + gridfinity 1x1: https://www.printables.com/model/340502-pokit-compact-multimeter-gridfinity-1x1

Compact cutting pliers: https://amzn.to/3W5qyAR

Silicon usbc cable (great as they provide little physical resistance when moving them and placing them down) https://amzn.to/3Yy7exR

The solder tip cleaner was included in the original link but here is a stand alone release location, with links to the sponge for it: https://www.printables.com/model/341676-brass-solder-tip-cleaner-gridfinity-1x1

 

Designed with OnShape, edit it here.

 

Support

If this has been helpful to you please consider supporting my effort using the donation button at the top:

I have also created this sticker set perfect for your ultrasonic cleaner:

https://shop.kactuskrunch.com/product/ultrasonic-cleaner-10-sticker-sheet

Tagi