Flexier Rex
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
1,82 € – 2,23 € netto (bez VAT)
Dla pliku: Flexier-Rex-v3-PrusaI3MK3_0.2mm_PLA_MK3S_2h23m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,03 € netto (środek widełek).
- Masa podana przez autora
- 18 g
- Czas druku podany przez autora
- 2,38 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Extra flexible variant of the Flexi Rex
- Ocena
- 4,737 / 5
- Polubienia
- 165
- Pobrania
- 2652
- Wydruki
- 33
- Wyświetlenia
- 8574
- Oceny
- 19
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Share Alike
This is a variant on the classic Flexi Rex, with some extra play in the shackles. This gives it extra flexibility, particularly in the sideways direction.
The larger slots in the shackles could result in prints of this model being less robust than the original Flexi Rex, so this variant might not be as kid-proof as the original. If you have any problems printing the regular Rex, don't start on this one before you have improved your print settings. It risks becoming too brittle especially when printing at smaller scales, so I recommend not going below 90% size.
The primary source for this model is its GitHub repository where you can find the latest updates, the model's history, and detailed instructions.
Go to my site for an overview of my other models (not all of them are published on Printables).
Attribution
This is a remix of Kirbs' Flexi Rex (Thingiverse thing:1759297), based on airfish's remix (Thingiverse thing:2189652). That model in turn was most likely inspired by the ‘Flexy Rex’ by zheng3 (Thingiverse thing:929413).
Update 2024/04/01
Applied same tail pieces tweak as the regular model, to make it even easier to balance the Rex on its tail.
Licensing
This is published as a straightforward variation on the Flexi Rex, hence it falls under the same Creative Commons Attribution - Share Alike license, and the same conditions apply. See the top-level README of the Flexi Rex repository for all the details.
Print instructions
The recommended print settings are the same as for the original Flexi Rex:
- 0.2 mm layers,
- 3 perimeters,
- 15% infill,
- solid infill threshold 8 mm²,
- 5 top layers and 4 bottom layers,
- no supports and no raft needed.
Expect about 2.5 hours print time for a good quality print.
Don't use a high infill value, this could cause it to become unbalanced. For improved stability, you could increase infill on the piece with the feet below it, but this should no longer be necessary with the newest model.
A PrusaSlicer 3MF project file with the recommended settings and a pre-sliced gcode file are provided for the i3 MK3.