1 / 5
FGC68 MKII tipx edition: Dye Half mag UAL Upper and lower set for first strike use — zdjęcie 1
1 / 5

FGC68 MKII tipx edition: Dye Half mag UAL Upper and lower set for first strike use

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

dye half mag version

Ocena
0 / 5
Polubienia
11
Pobrania
100
Wydruki
0
Wyświetlenia
893
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

11-10-2024
M5 nut lower have been added. for a stronger connection

it will use a 30mm long M5 bolt with 3d printed grips
-------

FGC68 GEN2 Updarted 

the link to the new manuals and parts list can be found here https://drive.google.com/drive/folders/1POafTye0p9ps3qhr2-nWT2uAPL3kko1u?usp=sharing

____________________________

this lower and Upper will work with the basic FGC68-MKII parts.
this set will make it possible to use dye half mags with the FGC68 platfrom

the FGC68 starter set can be found here:
https://www.printables.com/model/87803-fgc-68-base-package-starter-set-for-tipx-tcr-magfe

the collection of FGC68 parts can be found here:
FGC68 MKII
https://www.printables.com/social/180009-untangleworks/collections/88908

FGC68 MKI
https://www.printables.com/social/180009-untangleworks/collections/88907


some of the installation steps that are different from the TIPX lower can be fund in the images for now

-

marker parts: 
long range kit for TIPX or TCR internals for first strike use

I have not tested if the stock TIPX round shaped breach will match well with the Plant eclipse followers... for round-ball only use

-
mags parts:

self made dye half mags or the UNW DHM mag shells.
and you will need the PE followers the official ones. or the 3d printed PE replica.
note: you don't have to use the special Lok-bolt followers that I made. the stock shape of a PE follower should work like a bolt stop

the DYE Half MAG parts that I made can be found here. (half mag shells, followers)
https://cults3d.com/en/design-collections/UntangleART/dye-half-mag-parts


-

materials needed lower mag release:
paddle release
1x spring 6mm OD, 0.6mm wire, 12mm long
1x bolt m2 16mm long

L part
1x m3 bolt in a length of 25mm

FGC9 mag release paddle
1x metal pin 4mm OD, 27mm long (a 3d printed part can be used for this)

-

print settings:
0.2 layer hight should be fine.
you can use the 8 layer walls and a 40% infill.
but personally I moved a bit over to solid prints just to give it more strength in case things go wrong on the field…

movies:

UNW FGC68MKII new lowers for the T15, TMC and Dmag / helix mags for this magfed paintball marker
https://www.youtube.com/watch?v=xjbmq-A3C3c
https://odysee.com/@UntangleWORKS:a/UNW-FGC68MKII-new-lowers-low:f

FGC68 a small update on the installation of the new lowers for TMC T15 Dmag mags
https://www.youtube.com/watch?v=PwSyvEeVHTk
https://odysee.com/@UntangleWORKS:a/FGC68-Bolt-update-on-lower:a

Tagi