1 / 2
Front brace w/ integrated Y belt tensioner for Anet A8 — zdjęcie 1
1 / 2

Front brace w/ integrated Y belt tensioner for Anet A8

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A front brace to reinforce the Anet A8 and similar printers acrylic front plate with an integrated Y belt tensioner.

Ocena
0 / 5
Polubienia
0
Pobrania
6
Wydruki
0
Wyświetlenia
91
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

I made this several years ago and it has been sitting as a draft because I forgot to add images. Not sure how many people are still rocking the A8, but just in case I figured I better get it out there…

I upgraded to a beefier bed carriage because the original Anet 3-piece part wouldn't properly align and my Igus Drylin linear bearings kept binding and causing Y-axis layer shifts. However, the new carriage wouldn't clear my existing tensioner, a style with the tensioning screw above the acrylic front plate. The only one I could find that didn't have this type of adjustment relied on a large 3d printed screw which I don't really trust. So, I designed this to not only tension the belt with a beefy M4 screw but to reinforce the acrylic on which the tensioner relies. 

I took inspiration from many, many designs across Printables and other platforms. However, this way overengineered model itself was designed from scratch by me. I wore out 3 caliper batteries in the process, but this was both a learning experience for me as it pushed my Fusion 360 and logic skills into new territories learning about torque forces and how stresses transfer from one part to the next. I doubt it's perfect because I'm an amateur, but it's still quite strong.

You will have to drill some holes though. None of the existing Anet holes would give me what I wanted in terms of strength. I've included a printable drill marking guide. It should clip onto the plate and let you mark with a marker or paint pen where to drill. I don't recommend drilling through the guide as the drill will reduce the accuracy of the holes, but you do you. The best way I found to drill it was to remove the front plate entirely and lay it on a block of wood to keep the acrylic from blowing out when the drill bit gets through. 

Hardware list:

  • m4x14: 4x - for the 4 outside corners
  • m4x16: 2x - goes above and below the tensioning screw
  • m4x40: 1x - for the tensioner
  • m4 nuts: 7x
  • M4 washers: 8x - One for each of the fastening screws and 2 for the tensioning screw
  • m3x18: 1x - for the tensioner bearings
  • m3x30: 1x - for the tensioner pivot

If you don't have these sizes in your collection already, you can get them in assortments available on Amazon. The quality isn't as good as what you can get from McMaster-Carr but for this application, it's fine & much cheaper.

Installation:

  • Use the drill guide to mark your holes
  • Remove the guide and drill the holes
  • Install the 6 fastening screws from the outside, making sure to use a washer between the screw head and the acrylic. The M4x14 screws go on each of the corners and the m4x16 screws go in the middle (above and below the actual tensioner screw) where the model is thicker.
  • Insert your Y-axis belt bearings into the tensioner (making sure to get the belt in there if you're not removing the belt entirely) and use the m3x18 screw to attach
  • Attach the tensioner to the pivot using the m3x30 screw
  • Insert the m4x40 screw for the tensioner. I recommend 2 washers here for some “slippage” when adjusting. It's a bit overboard, but oh well. 

 

Tagi