1 / 8
1-4s BT2.0 Whoop Lipo Series Charger — zdjęcie 1
1 / 8

1-4s BT2.0 Whoop Lipo Series Charger

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

1-4s BT2.0 Whoop Lipo Series Charger Building and using this can be, quite literally, explosive. Please know what you…

Ocena
0 / 5
Polubienia
4
Pobrania
20
Wydruki
0
Wyświetlenia
398
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution

1-4s BT2.0 Whoop Lipo Series Charger

Building and using this can be, quite literally, explosive. Please know what you are doing and test somewhere that wont catch on fire, like a garage or even outside. Please ask someone who knows to take a look at your wiring as a sanity check. If you don't have a basic understanding of electricity, stop here. BUILD AT YOUR OWN RISK.

Required Materials:

  • xt-60 connector
  • 4s Balance lead
  • 4x bt2.0 (male and female)
  • 16ish AWG wire

Instructions

  • Print bt2_top.stl out of pla.
  • test fit the male (male pin female plastic) to make sure it fits. It should be somewhat snug
  • apply a bit of super glue to the edges of those male bt 2 connectors and insert into their slots, let dry. thicker stuff/gel is probably better here.
  • plug female (female pin male plastic) bt2 ends into their male counterparts, this will keep them from deforming while soldering
  • solder in a series the bt2 plugs (positive to negative.) Do NOT complete the circuit by connecting the far ends, just doing the white and blue wires as shown.
  • solder ~16awg wire to the first negative and last positive in the chain, then solder on the xt-60 appropriately.
  • solder the balance leads to each positive as well as the first negative.
  • you can try to use heat shrink to cover the exposed ends, but man that isn't easy, its super tight. I just used some e6000 to cover the exposed leads, but liquid electrical tape is likely better.
  • Print bt2_middle.stl out of pla, run wire harnesses through the big hole in the top and out the front.
  • while leaving them plugged in, solder female (female pin male plastic) bt2 into jumpers. (short them with a bit of wire). These will be used to jump the circut that way you can do 1-2- and 3 at a time if you dont want to do 4. Keep in mind you have to have these in the proper order. so that 1s is 1-0-0-0 not 0-0-0-1 or 0-1-0-0, otherwise your charger will yell at you.
  • test to make sure it works
  • Print bt2_bottom out of pla.
  • glue the bottom on with some super glue
  • glue the middle to the top with a little but of super glue.
  • (optional) print bt2_slide.stl out of tpu and slide over the whole thing, this just makes it stay together better in a bag and it looks nice.

Changed in remix

  • only has 4 connectors to save cost on bt2, ....and all i had sitting around was a 4s balance lead
  • made it taller to fit the wires
  • added the tpu band
  • opened up the wire exit holes
  • Idk how his jumper was working, so i didnt use it.

Category: R/C Vehicles