1 / 7
Beautiful TPU Feet for Prusa Mk3S+, Prusa Mini and  Ender 3 — zdjęcie 1
1 / 7

Beautiful TPU Feet for Prusa Mk3S+, Prusa Mini and Ender 3

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

May or may not lesson vibrations and noise from your printer or foam rubber pads with these shock absorbing TPU feet

Ocena
4,333 / 5
Polubienia
24
Pobrania
179
Wydruki
3
Wyświetlenia
1427
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Please read all instructions before installation on your printer

Introducing my shock absorbing feet. These are made out of TPU and are engineered to resist and reduce vibration, shock and noise transmission of your printer into the table or surface it's resting on.  Please note, I like these feet for their aesthetics, they also raise the printer up to allow for better cable management.  I believe they do provide some additional noise and vibration resistance, but your mileage may vary depending on the make of TPU material used to print with, printing temp, infill etc.

Once installed these will provide a very nice upgrade to your printer. 

Models For:

Prusa Mk3S+ and previous models with 30x30 bottom rails

Prusa Mini and clones that use 30x30 bottom rails

Creality Ender 3/3Pro and clones tha use 40x40 bottom rails

These are easy to install on the Ender 3 and clones as you just slide onto the 40x40 tracks. The Prusa printer will require some slight disassembly to install or install during assembly for the easiest install. 

*Make sure your printer is level and does not rock before installation. After installation please recheck it still does not rock or wobble, these should not affect a properly leveled printer. 
 

Prusa Mk3S+ Note: If disassembling your nicely assembled and calibrated printer is not for you, just use the “mk3_foot_v2_retrofit” foot that will slide on without disassembly. It takes some downward force to get the foot on, but it does stay on after installed.  You may want to recalibrate just incase to make sure you did not disturb anything during foot installation. 

Prusa Mini Note:  If disassembling your nicely assembled and calibrated printer is not for you, just use the “mini_foot_v2_retrofit” foot that will slide on without disassembly. It takes some downward force to get the foot on, but it does stay on after installed.  You may want to recalibrate just incase to make sure you did not disturb anything during foot installation. 

Important: When you put these feet on the Prusa Mini, you will need to stack three of the old (7.8mm) feet together and place under the Z-Axis arm and control board so the Mini will be more stable.  

Creality Ender 3/3Pro Note: These are prety easy to install and should only requre minor parts removal or partial removal to get these feet on. 

Please note: These feet are the real deal. They’re not the flimsy stuff that comes with your printer. They are industrial grade, heavy duty support your printer deserves. They take a while to print, about 6-8 hours for the Ender 3 and the Mini and 10.5 hours for the Mk3S+, but they’re worth the wait. Print yours today, you’ll be glad you did!

Printing

Place on side on the build plate 

Filament - TPU

Infill - 15% is good

Layer Height - .30mm

Supports - None

Parimeters - 2-3 

Additional Parts - None

Bed Adhesion - Glue stick is recommended

Rafts - None

Scaling - None

Filament Change - None

Post Printing Notes:  None

Happy Printing!

You can help
To help cover the expenses of printing prototypes for the models I share, please consider a donation by purchasing an item from my Amazon wishlist here

Please leave a comment and let me know how you like this model. 

Here are my other similar models related to 3D Printing

printables search – 3dprinting @HandyHandcrafts

Also, check out my other models over here:

https://www.printables.com/social/130916-hendersons-handcrafts/models

Award winning Model “Japanese Toolbox” for the "Box Contest: here:

https://www.printables.com/model/260100-japanese-toolbox-inspired-locking-lid-box                                                       

Below are just few of my other models

Tagi