VOROD CLONE - Inspired by VORON 2.4, S.T.E.V.E, & V1-MPCNC/MP3DP
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
WARNING DRAFT - Inspired by VORON 2.4, V1-MPCNC/MP3DP, & S.T.E.V.E - WARNING DRAFT
- Ocena
- 0 / 5
- Polubienia
- 7
- Pobrania
- 20
- Wydruki
- 0
- Wyświetlenia
- 1009
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Inspired by VORON 2.4, V1-MPCNC/MP3DP, and heavily leveraging S.T.E.V.E gantry.
Parts are being designed & printed on the fly as construction is completed. My apologies in advance to anyone who expects this to be a finished project. Do not start printing these parts without understanding that you may have to finish designing your own components, or print newer versions as adaptations are made. Solution is far enough along in the build that parts and design are ready to be shared. Pictures to be posted, as build progresses.
Currently printing the current version in the highest glass transition temp PETG available 80C. This is done in the full knowledge that a complete rebuild with ABS parts could be the first job once this printer and enclosure are completed.
Budget COREXY based on ¾" or ½" (18mm) steel conduit. (I am currently constructing a hybrid because I have a lot of old ¾" conduit laying around from a previous project, thanks MPCNC…
- All parts should be printable without support, there are some large overhangs, 13mm in the Z_Bearing_Blocks. I used 25% print speed for overhangs and rotated the parts to make sure the first overhang layer had the shortest path.
- In the spirit of the VORON 2.4, the design should leverage 6mm GT2 belt vs lead screws to raise and lower the corexy gantry. One of the design goals was to remove more than $100 in linear rail guides and complicated conversion pulleys. Plan on using GT2x16T, micro-stepping and .9 degree steppers on the Z-Axis to achieve 400 steps / mm resolution. (Is this even required).
- All fasteners or machine hardware should be M3, and use M3 spaces/washers and locking nuts to control costs and retain flexibility.
- The design should minimize the purchases of custom hardware, rods, or tubing except where required to address issues with printing speed / tolerance.
- Should require no more than 1 KG of filament at 20% infill.
- Should support 1 ft^3 printing 300x300x300 area with 20' of standard electrical conduit, less than $50 at time of publication.
- Really wanted the design to be symmetrical, any advise on how to avoid mirroring the parts for the z-gantry, would be welcome. Attempted a central belt tension / management system but could not get a design to work reliably.
- Design is cubic 450mm, 600mm
Assembly instructions;
find a build table you can walk around without moving things too much during assembly, this really helps with the alignment of the cube.
Print the tri-corner pieces, every corner needs two blanks and one of either a stepper or a pulley corner. The parts pictured were printed in PETG with a .6mm nozzle, .3mm layer thickness, three walls/tops/bottoms, with 20% straight lines for infill. If you can print ABS, start with ABS.
All tri-corner pieces in the size of preferred conduit should be printed prior to assembly. See the photos above, parts should be prepared using an iron or heat gun to set the nylock or regular nuts in the nut races, 3 nuts per piece. If you are using nylock parts, thread an M3 bolt through the tri-corner piece, and into the nylock nut until it is flush with the top of the nut. Then use a soldering iron to gently press the piece into the corner nut race. This part should probably be modified to use M3 inserts like the Vorod 2.4, but…
When all three tri-corner parts have nuts set in them, thread the M3 bolts through washers and into the round parts of the face, don't feed them all the way in, leave them sticking out about 2mm. Don't skimp on the washers here, you will be torquing these bolts down to hold conduit firm when the rough assembly is completed, you don't want to pull the heads through the part. If you are using button head parts, you might be OK without washers, hmm.
Use something to space the tri-corner pieces as you tighten down the nuts. You want about a 2mm gap for assembly otherwise the parts will bind on the conduit and these big levers/pipes will crack your parts if they are already tightened all the way down.
Cut your conduit bottom and top pipes the length of your 8mm XY linear rods…you can adjust the pipes in the tri-corner mounts to the “exact” length you need for operation, but you will find that it is hard to compress your frame to match the linear rods if they are too long.
Assemble the bottom and top separately, leaving the vertical shafts/guides for last. You may need to print sleeve adapters depending on your solution for vertical rods. If anyone can source some type of LM18 bearings for a reasonable price, ping me, I would be interested in trying them out.
Assembly parts list.
| Qty | Spec | Part description These may help you when sourcing parts online. |
| 8 | 1812 Sleeve bushings | Oilless Bushings 18mm Bore x 20mm OD x 12mm Length Plain Bearings Wrapped Carbon Steel Base |
| 100 | M3 x 20mm | Full Thread Hex Socket Head Cap Screws Bolts, 2.5mm tool size |
| 100 | M3 Washer | Flat spacer for M3 threaded screws 3mm Inner Diameter x 7mm outer diameter x .5mm depth |
| 100 | M3 Nylock | Nylon inserted self locking nuts |
| 4 | 8mm linear rod | Stainless steel round straight linear motion shaft rod Length as required to support S.T.E.V.E gantry. |
| 4 | NEMA 17 17HS4401 | Z-Axis NEMA 17 Stepper Motor, 0.9 degree motor 1.3A |
| 6 | GT2 16T Drive pulley | GT2 16 Teeth 5mm bore timing pulley for 6mm belt. |
