da vinci mini printer display (heated print bed - see comments)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Printer display for da vinci mini w (heated print bed - see comments) In case I have to run long prints, I wanted to…
- Ocena
- 0 / 5
- Polubienia
- 7
- Pobrania
- 34
- Wydruki
- 0
- Wyświetlenia
- 682
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Printer display for da vinci mini w (heated print bed - see comments)
In case I have to run long prints, I wanted to see the printer status without running the PC. Since there was no mobile app from the manufacturer, which provides this function, I have a Raspberry Pi used. The program is written in processing and typed very roughly and quickly together. It shuts off as soon as the runtime drops below one minute. one could add further functions, e.g. the filament change or similar, which I did not implement. So you can improve or tinker with the program. A feedback about this would be interesting, thanks.
A known mistake. The USB switch always selects the device that was last turned on. So if you boot the PC up again while the connection to the Raspberry exists, the program will hang because the communication was severely interrupted. I have not installed error handling so far.
I'm using a Pi2B and a Wi-Fi stick so I can display the information with vnc on other devices.
some parts:
raspberry pi 3
https://www.amazon.de/dp/B07BDR5PDW/ref=cm\_sw\_em\_r\_mt\_dp\_U\_LB9ECb48DNYZ6
Quimat 3,5'' Zoll inch Touch Schirm Monitor 320* 480 Auflösung TFT LCD Display
https://www.amazon.de/dp/B06X191RX7/ref=cm\_sw\_em\_r\_mt\_dp\_U\_9C9ECb3TNM9GB
USB Switch 2 Port USB 2.0
https://www.amazon.de/dp/B01CU4QCRS/ref=cm\_sw\_em\_r\_mt\_dp\_U\_LE9ECb27CKS6G
Print instructions
Unassociated tags: da vinci mini
Category: 3D Printer Accessories Summary
Printer display for da vinci mini w (heated print bed - see comments)
In case I have to run long prints, I wanted to see the printer status without running the PC. Since there was no mobile app from the manufacturer, which provides this function, I have a Raspberry Pi used. The program is written in processing and typed very roughly and quickly together. It shuts off as soon as the runtime drops below one minute. one could add further functions, e.g. the filament change or similar, which I did not implement. So you can improve or tinker with the program. A feedback about this would be interesting, thanks.
A known mistake. The USB switch always selects the device that was last turned on. So if you boot the PC up again while the connection to the Raspberry exists, the program will hang because the communication was severely interrupted. I have not installed error handling so far.
I'm using a Pi2B and a Wi-Fi stick so I can display the information with vnc on other devices.
some parts:
raspberry pi 3
https://www.amazon.de/dp/B07BDR5PDW/ref=cm\_sw\_em\_r\_mt\_dp\_U\_LB9ECb48DNYZ6
Quimat 3,5'' Zoll inch Touch Schirm Monitor 320* 480 Auflösung TFT LCD Display
https://www.amazon.de/dp/B06X191RX7/ref=cm\_sw\_em\_r\_mt\_dp\_U\_9C9ECb3TNM9GB
USB Switch 2 Port USB 2.0
https://www.amazon.de/dp/B01CU4QCRS/ref=cm\_sw\_em\_r\_mt\_dp\_U\_LE9ECb27CKS6G