1 / 2
Car phone holder with USB for Samsung S23 Ultra — zdjęcie 1
1 / 2

Car phone holder with USB for Samsung S23 Ultra

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

It's a phone holder with USB for charging and wired Android Auto for Samsung S23 Ultra using Spigen Tough Armor case.

Ocena
5 / 5
Polubienia
150
Pobrania
532
Wydruki
1
Wyświetlenia
10 226
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Compatible phone/case/cable:

  • Phone: Samsung S23 Ultra
  • Case: Spigen Tough Armor
  • Cable: PZOZ magnetic USB

The phone is pretty large and heavy. It's definitely possible to print the model out as is and add padding on the holder's sides to fit smaller phones. But I'd suggest checking out the modeling steps/tips to make your own for a better fit and more compact and slimmer appearance.

Modeling guide/tips is at the bottom of the page.

Summary:

The idea is to have a place to put my phone in the car. It allows easy phone-to-car connection/disconnection via USB cable, doesn't take much space, and hides the phone from direct sunlight.

Because it's out of the sunlight, and sits pretty low in the car, I made it out of PLA. But PETG would likely be safer.

My last one, which is made for a S10 Plus, was made of PLA as well. it didn't suffer any change in its shape after 3 years in service. The top temp averages to 90F or 32C at where I live.

 

The holder is mounted on the lower dash cover. 

There's a compartment available for phone charging in the 10th gen Civic in front of the shifter. However, that space is not well suited for leaving large phones like a S23 Ultra connected with a cable though, despite the car doesn't support wireless Android Auto.

With the phone in the holder.

The holder is mounted onto the bottom side of the dash cover with heavy duty double sided mounting tape.

USB cable is routed underneath the dash cover

The cable is secured with adhesive cable clips onto the backside of the dash cover. It's then connected to the main USB port linked to the head unit which the wired Android Auto requires.

Dry fitting the cable in the case

Before gluing the cases together, do a dry fit.

I had to modify the cable clamp a bit due to a 0.1mm measuring mistake during modeling (this has been fixed in the model uploaded). 

The USB cable need to be glued onto the cable clamp part. Preferably with something strong when cured but still removable like a B7000 or D6000 glue. For reference, I used B7000.

Also, I pushed the USB cable in a tiny bit when gluing. This way, when B7000 glue cures, which is slight rubbery, can help provide a secure connection between the phone and the cable.

The Magnetic USB cable I used

You can find the same one if you search “PZOZ Magnetic USB Cable” on Aliexpress. But I think any other magnetic data cable can work. I've never tried with regular type C cables, but I'd assume it will work as well. Should definitely work with Apple's Lightning cable though.

I got mine a few years ago. What I have is just the USB 2.0 version, but still enough for charging and Android Auto which is what I mainly use.

This is not an ad. I'm not sponsored by anyone.

Preparing for mounting

The section of the dash cover I decided to tape the holder on has a slight curve. So for the front and back end of the holder, I double stacked the tape for a better fit.

Sections of the top shell is designed to be solid. This is so mounting tape has a place to adhere.

Tips if you'd like to model your own

Again, my design only suites my combination of phone, case, and cable. 

  • Phone: Samsung S23 Ultra
  • Case: Spigen Tough Armor
  • Cable: PZOZ magnetic USB

The design only required basic modeling skills. It should be relatively easy to design your own.

Here's the rough steps I took when modeling my own:
  1. Measure the length, height, and thickness of my phone with the case on
  2. Connect the USB cable, and measure where the connector distance from the top and bottom of the case
  3. In modeling software, create a box representing the phone
  4. Create a shell for the box, and expand the internal dimensions with a 0.1mm clearance on all sides (to make the phone sliding in and out more easily). Cut roughly ⅓ to ¼ of the box off.
  5. Split the phone shell in half. One for the top, and one for the bottom.
  6. Add tongue/groove in the edge of the shell halves for easier alignment when gluing the cases together
  7. Add some venting holes to the shell, but leave enough flat surfaces for mounting on the top shell.
  8. Sketch out the USB cable's cross section. Doesn't have to be precise though. Any gap can be filled with tape/glue during assembly.
  9. Create a cylindrical shape from said sketch
  10. Shell the cylinder, make it a tube
  11. (optional) Add some clearance to the tube to allow for adjustment during gluing(i.e. Shimming with paper/tape to adjust the cable in the tube)
  12. Split the tube in half. One for the top shell, and the other for the bottom shell.
  13. Position the half tube based on measurement from step 2. Do this for both the top and bottom shell/tube
  14. Join the shell and tube, add some chamfers, round some edges, do some cleanup, make it pretty
  15. Extend one of the shell half's opening into a new component to make half of the lip
  16. Add some tongue/groove in the front of the shell and the lip. I just used the Draft tool in Fusion 360 to create the lip.
  17. Mirror the half lip to make it a 1-piece part.
Tips:
  • Watch out for any camera bump if your case isn't flat on the back.
  • When modeling, save a copy of the phone shell model and cable tube. It's likely you'll need to make adjustment to where the the cable tube needs to be.
  • Before printing out the whole thing, prototype a short-shell version to check for fitness. This is mostly helpful when adjusting cable tube position.

Thanks for reading this far. Happy printing. :)

Tagi