1 / 17
Snap-on extruder wind tunnel cooler for Prusa MK3S+ — zdjęcie 1
1 / 17

Snap-on extruder wind tunnel cooler for Prusa MK3S+

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Simple click-on extruder cooler for Prusa MK3S+

Ocena
4 / 5
Polubienia
2
Pobrania
21
Wydruki
1
Wyświetlenia
389
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

English version below. 💪😎

 

ČESKY

Jednoduchý, nacvakávací chladič (větrný tunel), pro Prusa MK3S+ extruder. Ke správné funkci je nutný 40x40mm větráček, bez něj větrný tunel bude naopak chlazení krokového motoru bránit. 

 

Já jsem použil tento: Noctua NF-A4x10 5V PWM - Ventilátor do PC | Alza.cz
…který je přes USB snadno napojitelný buď na USB hub, nebo do Raspberry PI.

 

Ventilátor je možné nechat volně ložený v tunelu, nevypadne a nehýbe se. Pokud bys chtěl(a) větráček fixovat, doporučuji buď tavnou pistolí zakápnout rohy větráčku k tunelu, nebo přilepit vteřinovým lepidlem hrany k témuž. 

Pro lepší estetický dojem je ideální protáhnout kablík větráčku mezi stěnou tunelu a lištou, viz fotografie. 😉😊

Celá tisková hlava díky tomuto aktivnímu chladiči získá uhlazenější design, ale hlavně se začne výrazně lépe chladit krokový motor podavače do extruderu. Tím se omezí tzv. “heat creep” vysoké teploty motoru na unášecí kolečko, který je hlavní příčinou zasekávání filamentu v tiskové hlavě. Tento problém nastává zejména při uzavřeném Original Prusa Enclosure, kde při delším tisku stoupne ambientní teplota nad 32°C a krokový motor začne tím pádem topit na nelidské teploty, kvůli kterým změkne filament při průchodu podavačem, rozšíří se a následně neprojde ani tiskovou chladící komorou do trysky, ani následně ven z extruderu “horem” - při pokusu o výměnu se přetrhne a je potřeba celou hlavu rozebrat a filament vyjmout ručně. 

Což znamená nenávratné selhání tisku, minimálně 20 minut práce a následnou kompletní XYZ rekalibraci, což je dalších cca 20 minut. 

 

Tento chladič této prekérii téměř zabraňuje a oddaluje moment, kdy k ní dojde.

 

Nicméně i tak zejména pro jistotu, doporučuji při delších tiscích PLA nepoužívat recirkulační, ale průtokový filtrační systém Enclosure, který vytáhne horkost ven a eliminuje riziko přehřátí filamentu a komponent, zejména v letních měsících. 😉

Jestli chceš, budu rád když mi koupíš kafe. 😉
https://ko-fi.com/punik

 

 

 

 

 

ENGLISH

Simple click-on wind tunnel cooler for Prusa MK3S+ extruder. For proper operation, it is necessary to have 40x40mm cooling fan! Without it, the wind tunnel will hinder the stepper motor cooling.

I have used this fan: Noctua NF-A4x10 5V PWM - Ventilátor do PC | Alza.cz
…which is easily connectable to either USB hub, or Raspberry PI.

It is possible to have the fan placed freely in the wind tunnel, it won't move much. If You want to fixate the fan, I recommend using either the hot glue gun on the corners, or fast glue on the edges of the fan. 

For better aesthetic look, it's ideal to guide the cable between the side of the tunnel and the snap-on assembly, just as shown on the pictures. 😉😊

The whole printing head will look more streamlined, but the main benefit is way better cooling of the stepper motor of the extruder, thus limiting possible heat creep, from the stepper motor to the filament. This problem occurs especially in enclosures as in Original Prusa Enclosure, due to ambient temp rising above 32°C. Above this temperature, the stepper motor gets too hot, just as the loading wheel, which by contact softens the filament, which then gets stuck inside the cooling chamber of the extruder. Recovering from this can take approximately 20 minutes to disassemble the extruder at least, and approximately 20 minutes of complete XYZ recalibration, not mentioning the failed print time and loss of filament.

 

This cooler almost prevents this, and postpones the critical temperature moment a lot.

 

Still, even with this cooler installed, I would reccomend using pass through filtration system instead of recirculation one. Especially when printing PLA filaments, in the summer or heated environment. 😉 Or when printing large items, with printing time exceeding couple of hours. 

If You want, I would appreciate If You bought me a coffee. 😉
https://ko-fi.com/punik

Tagi