1 / 7
3DG v1.1 - Full Sized Acoustic Guitar printable on an Prusa i3/Ender 3/X1C/P1P — zdjęcie 1
1 / 7

3DG v1.1 - Full Sized Acoustic Guitar printable on an Prusa i3/Ender 3/X1C/P1P

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Fully 3D printable, 00 sized acoustic guitar. Printable on an Prusa i3/Ender 3/X1C/P1P size machine or larger.

Ocena
0 / 5
Polubienia
112
Pobrania
780
Wydruki
2
Wyświetlenia
6888
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Music
Licencja
Creative Commons — Public Domain

Based off original 00 acoustic guitar plans by Grellier Guitars (https://www.grellier.fr/en/downloads). Scale length is 633mm (24.9in), with 20 ‘frets’.

Changelog:
3DG v1.1
I finally got around to printing one of these! And like with any untested design, I found some problems immediately! Specifically, the joint between the head block and the sides was not sufficiently strong. I am making an update to this joint, adding a secondary mating feature between these parts. This update affects the following parts:
S1
S2
Head Block

If you are downloading the files for the first time, this does not change anything for you! All files on printables are correct. Note that I have not gotten a chance to update
any drawings or screenshots to reflect these changes. However, the changes will not affect the assembly process. Lastly, I may increase the tolerance between fitted parts in the future. I have found that the quality of the fit of parts can be highly dependent on filament. 
If you build a 3DG yourself, feedback on this would be appreciated!

 

Description:

I would like this to be the beginning of a family of 3D printable guitars! The next additions I am working on are a complete fretboard, a 12-string version, and possibly an 8 string version :).

All of the parts of this model fit on the bed of an Prusa i3 or Ender 3 (~220x~180 or smaller). The pieces use dovetails or other kinds of joinery to make the build significantly easier than a traditional wooden acoustic guitar. With this design, a mold should not be necessary. All fitted parts have a 0.200mm gap to accommodate less accurate printers. Sharp corners are also rounded in a way to accommodate printers without pressure/linear advance. For now, this guitar is fretless. I am in the process of designing a board that will fit fret wire, and another with markings, but also no frets. The pieces will need to be glued together, likely with thick CA glue (superglue) or something comparable. (Note: adhesives that expand when they dry, for example gorilla glue, will not work for this build)

I am still in the process of printing this myself. Until I string my first one up, I cannot be 100% sure this will actually work. I have only just finished designing this, but am excited to share it and get feedback. Build instructions are a work in progress. For now, this is how the parts are named: B=Back, BB=Back Bracing, F= Fretboard, N=Neck, S=Sides, T=Top, TB=Top Bracing, W=Waist blocks. Parts are numbered roughly from left to right, top to bottom

The strings on a guitar put a significant amount of force on the neck. For this reason, I recommend only ball end nylon classical strings.  Steel/Electric strings will not work! Something like this:

https://www.amazon.com/Manhasset-Classical-Guitar-Strings-NEW-M260/dp/B07CVM2GZL?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=ATVPDKIKX0DER&th=1

There are also slots in the neck for neck reinforcement rods. You can buy nice ones from places like StewMac, but even something simple like a few pieces of wood would also be good. The point of this would be a continuous piece of material that spans all of the joints in the neck. Metal neck reinforcements will make your truss rod adjustments more stable, at the cost of making adjustments more difficult. 

Additionally, the neck is designed to fit a 12 ¼" StewMac Hot Rod Low Profile truss rod. Other generic truss rods will probably also be fine. Just make sure to buy a 2 way truss rod, not one way.

Next, you will need tuners. Any cheap set will do. Electric ones are fine as well.

You will also need bridge pins, a nut, and a saddle. Any will work, and you could might even be able to 3D print them, too. I may end up designing some in the future. I will add some pictures of the dimensions of the saddle slot and nut-area of the neck soon.

Print/material recommendations are a WIP. Of course, some kind of wood filled material is tempting, and I would say standard fill-material-rules apply. An abrasive-resistant nozzle is ideal, as well as 0.6mm or larger. A large nozzle will also cut down the (significant) print time of these parts, as large as possible is probably best, unless you plan to sand and properly finish your piece. For print settings, I would recommend that, at a minimum, the top and neck are printed solid. You might be able to get away with high wall count (4 or more), and high infil (40 percent or more) on the neck. 

Guitar setup instructions are probably outside the scope of this guide. Assuming your guitar has not exploded when you string it up and tune it for the first time, there are many great videos on you tube on how to set up a guitar printing a fretless version also has the benefit of reducing the time and tools required for setting up frets (it is a significant amount of time and specific tools). The most important thing will be truss rod adjustments. The plastic you choose to print your guitar with will likely have a large impact on the behavior of your truss rod. In general, plastic is much more ductile than wood, so I would expect a plastic guitar to need more adjustment than a wooden neck. That being said, plastic does not absorb water the same way wood does, so once you are happy with your setup, it likely will not change very much on its own.

Thank you for taking the time to read! And happy printing!

Tagi