1 / 8
Amateur Radio SpiderBeam Antenna Pole Add-Ons — zdjęcie 1
1 / 8

Amateur Radio SpiderBeam Antenna Pole Add-Ons

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The perfect add-ons to make your SpiderBeam antenna pole rock!

Ocena
0 / 5
Polubienia
7
Pobrania
97
Wydruki
0
Wyświetlenia
813
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution

I recently purchased a SpiderBeam 40" expandable fiberglass pole for use in the field with my ham radio gear. It's a great product but I found a few useful items to print for it. This is a collection of those things.

All are printed in PETG with a 15% infill. No supports.

1. Top Cap: The pole comes with 2 heavy rubber end caps. They work well but are a little tough to remove and since both look identical it's hard to tell which end of the tube to open. This is a new cap that I put on the end that you open. It also gives it about another 1/2" or so inside which help facilitate the other stuff below.
2. Guy Wire Ring: A ring that fits over the top of the main pipe and allows for 3 guywires to be extended from it for support.
3. Guy Wire Supplament: A 2 pronged addditon to the Guy Wire Ring which allows a cord to be anchored like it is on a flagpole. This needs four M3x16 self-tapping screws to attach it to the GuyWire Ring.
4. Base Hub: A large ring that can be nailed into the ground. The base of the pole then slides into it and it holds it firm.
5. Top: A piece with 2 eyelets which I glue to the top of the smallest pole using JB Weld. I can then easily attach things to it and raise it.
6. Tensioner: (Print 3) Used to easily tighten my guy wires once installed.
7. Stake Top: (Print 3) These slide over standard 10" galvonized nails. I use 3 nails in the ground - one at the end of each guy wire.
8. Bottom Plug: This gets glued into the 2nd smallest pole ON THE BOTTOM. This alleviates the smallest (center most) rod from slamming down on the "Top" piece that is glued to it.
9. I absolutely love this cord winder on Thingiverse: https://www.thingiverse.com/thing:2545697

So here is my kit that now goes with my SpiderBeam (includes all of the pieces above):

1. Small hammer (I bought a 6" one off Amazon)
2. Three 8' paracord ropes with loops tied in each end and a rope tightener on each. I use reflective so the guy wires are more visible. From Amazon I bought a 100' roll of 550lb paracord, cut three 8' pieces and used a lighter to seal off the ends.
3. Tie 2 loops in the residual portion of the paracord (about 76' and seal the ends with a lighter. This is used to raise stuff up the pole. I organize my antenna stuff and then use this paracord to raise it up. The paracord is then tied off to the Guy Wire ring.
4. Five 10" galvonized nails. Three for the guy wire ends and two for the Base Hub.
5. 8 carabiners. I bought a set of 10 three inch ones from Amazon. 
  A. Each guy wire has one at the base (goes into the Stake Topper after it's placed on the nail head, and one at the top of each guy wire on the Guy Wire Ring. The tension ropes then click into the bottom carabiner and loop through the top carabiner. The rope tensioner is then used to tight them from the top.
  B. I put on in the Top piece eyelet and run the paracord used to raise the antenna through it.
  C. I put on on the paracord used to raise the antenna to tie the 2 loops together and hold them while I put the pole up.
6. The other thing I carry is the cord winder to hold the long paracord used to raise the antenna. I tried using the little hand ones but the cord is constantly getting twisted and turned so it wants to kink.

Another not - I found that with heavier antenna wire I do not raise the last section of the pole. Instead I leave it in the 2nd sleeve. This shortens the pole by 4' but the top section is much more rigid.

Hopefully that's enough to get you going. I design everything in OpenSCAD which is free to download and use. I am including the source files here as well.
 

Tagi