1 / 2
Inland Cardboard Spool Replacement — zdjęcie 1
1 / 2

Inland Cardboard Spool Replacement

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Spool replacement for Inland cardboard spools. The spool fits inside Bambu Lab AMS.

Ocena
0 / 5
Polubienia
11
Pobrania
122
Wydruki
0
Wyświetlenia
1413
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial

I really like that Inland filament has moved over to cardboard spools. I got tired of throwing away plastic ones and cardboard spools work great on my Ender 3 printers with a center hole filament holder. 

I recently got a Bambu Lab X1 printer and word on the street is cardboard spools may not work well in the AMS. I have some reusable spools for Inland Spooless filament, but they do not fit in the holes left after the sides of the cardboard spools have been removed. 

This spool design fits inside the hole left after peeling off the sides of the cardboard spool. It uses an M6 bolt and nut. If you have a reusable spool from Microcenter, it uses those bolts. My reusable spool came with an extra set of bolts and nuts. 

What you will need:

  1. spool of Inland filament on a cardboard spool
  2. 2 - Inland Cardboard Spool Replacement pieces. Print two of these parts.
  3. 2 - M6x50 bolts with nuts. A little shorter will work. Measure to make sure.
  4. a knife or box cutter. Sometimes the glue holding the spool sides on has a little overhang that needs to be trimmed back after removing the sides.

Before you begin, make sure the bolts and nuts fit inside the bolt and nut holes in the Inland Cardboard Spool Replacement pieces. DO NOT remove the sides of the cardboard spool unless you can bolt the new sides together. 

You have been warned.

If you have an empty cardboard spool, test the below steps on that spool first if you are unsure or nervous. 

To replace the sides of the cardboard spool:

  1. Secure the end of the filament in some way other than connecting it to the side of the spool.
  2. Lay the spool on its side on a table or other flat surface.
  3. CAREFULLY and SLOWLY peel off the side of the cardboard spool. Do not touch the filament. You do not want it coming loose.
  4. Work your way around the spool and lift the side until it comes off.
  5. If there is any glue or paper covering parts of the hole, use the boxcutter to remove it. Be careful not to touch the filament. 
  6. Put one of the Inland Cardboard Spool Replacement pieces inside the hole and press it completely down. 
  7. Repeat for the other side making sure the side already done does not come off. 
  8. Once both sides are replaced, line up the bolt holes and bolt the side together. It does not have to be too tight. Just enough to hold the sides together. 

This video shows how to install it: 

That is it. I am sure this part will fit on other cardboard spools, but I only have Inland filament to test it with. If you find it works with other spools, leave a comment so others will know.

Print Settings

Rafts/Brims:

No

Supports:

Not really. Adding supports in the bolt holes will give you cleaner holes, but they should print fine without supports. 

Layer Height:

0.28 mm

Infill:

10% - 15%

Filament: PLA works fine as will any other filament. 

 

Updates:

4/8/2023 - Spool_v2.stl - I made the nut holes a little bigger. The original version prints fine on my Bambu Lab X1, but on my Ender 3 they were a little tight. 

Tagi