1 / 19
Scara Mechanism for Kinetic Sand Art — zdjęcie 1
1 / 19

Scara Mechanism for Kinetic Sand Art

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This mechanism is intended to be used with kinetic sand art enclosure:https://www.thingiverse.com/thing:5991171 Its…

Ocena
0 / 5
Polubienia
60
Pobrania
208
Wydruki
0
Wyświetlenia
2396
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial

This mechanism is intended to be used with kinetic sand art enclosure: https://www.thingiverse.com/thing:5991171 or https://www.printables.com/model/475686-kinetic-sand-art-tabletop-enclosure

Its motion is limited to the X-Y plane. This is a remix of Woobag85's 'Work-in-Progress'. This design is slightly smaller and does not require specially machined 60T pulleys. Note that the Elbow Arm Hall Effect Sensor shown in the photo has been relocated to the rear of the Lower Frame in the final design.

 

Bill of Materials

Components:

(2) Stepper Motor, Nema 17, 5mm Dia. Shaft with flat

(1) Shaft, Brass, Elbow, 5mm Dia. X 55mm Lg.

(1) Shaft, Brass, Shoulder, 5mm Dia. X 130mm Lg.

(2) Pulley, G2T, 20T, 5mm Dia Bore, 6mm Belt

(2) Pulley, G2T, 60T, 5mm Dia Bore, 6mm Belt

(1) Pulley, Idler, G2T 5mm Dia. Bore, 6mm Belt

(2) Shaft Collar, Steel, 5mm I.D. With Set Screw

(2) Belt, G2T 158mm Continuous Loop, 6mm

(1) Belt, G2T 280mm Continuous Loop, 6mm

(2) Magnet, 3mm Dia x 2mm Neodymium N50

(1) Magnet, 1/2” x 1/2” Neodymium N42

(8) Bearing, 625 16mm O.D x 5mm I.D. X 5mm

(2) Hall Effect Sensor A3144

(1) Controller (Minimum X&Y Axis) processing Gcode

Hardware:

(10) M3 Flat Washer

(2) M5 Flat Washer

(5) M4 x 16mm SHCS

(3) M3 x 16mm SHCS

(1) M3 Locknut

(13) M4 Hex Nut

(3) M4 x 10mm Cup Point Set Screw

(9) M3 Hex Nut

(10) M3 x 10mm SHCS

(3) M3 x 10mm Cup Point Set Screw

(4) M5 x 70mm Pan Head Machine Screw

(5) M5 Locknut

(2) M4 x 12mm SHCS

(1) M5 x 20mm Pan Head Machine Screw

(4) M4 Flat Washer

(2) M4 x 12mm Pan Head Machine Screw

(4) M3 x 12mm Pan Head Screw

Printing:

Use .015mm layer height for the 60T pulleys. If bridging is poor, use a cylindrical build plate support at the center bore. Internal holes in horizontal surfaces are closed over with a single layer for improved bridging. Clean out the holes before assembly.

Use PLA for the Shoulder Arm with 4 perimeters and 30% infill

Use PETG for the Elbow Arm

The Controller Mount is controller specific. Modify the mount to fit your preferred controller.

A STEP file of the entire assembly has been provided.

4/21/2023 Added missing Frame_Upper.stl

Print Settings

Printer Brand:

Prusa

Printer: 

I3 MK3S

Rafts:

No

Supports: 

No

Resolution:

0.15mm and 0.20mm

Infill: 

20% and 30%

Filament: Prusa PLA and Prusament PETG PLA and PETG Black and Orange Completed Application =====================

 

 

 

Category: Robotics

Tagi