1 / 10
Wolfcraft Repair Kit 3455100 Reparatursatz — zdjęcie 1
1 / 10

Wolfcraft Repair Kit 3455100 Reparatursatz

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

So I have two of these and a while ago one had a broken spring. It didn't work anymore which is why I came up with…

Ocena
0 / 5
Polubienia
4
Pobrania
42
Wydruki
0
Wyświetlenia
295
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

So I have two of these Wolfcraft clamps and a while ago one had a broken spring.

It didn't work anymore which is why I came up with this repair kit.

The kit consists of the two printed parts as well as three parts you need from the original body.

It's the little metal plate with the rectangular cutout, the original lever bolt and also the rubber cover.

These parts should be fine even after the clamp doesn't work anymore.

Rubber cover and metal plate go to the top and back of the printed body.

Then the printed lever get's fixed by the bolt.

The fittings are pretty tight, but that's on purpose.

Anyway until now I have only this one broken clamp, so please tell me, if these tolerances work for you as well.

Also the fitting on the original rod is very tight.

I intended to let the material set after being mounted and I think it's good now.

It could be slightly easier to move, but it's better than having the body always slip away.

Maybe there's still support left near the rod which hinders it, but anyway it's alright.

So enjoy and I really hope this thing helps you out. :-)

_________________________________________

 

Deutsche Beschreibung:

Bei meiner Wolfcraft Klemme ist eine Feder gebrochen und anschließend konnt ich damit nichts mehr fixieren.

Daher dieser Reparatursatz bestehend aus den beiden Druckteilen, und drei Teilen aus der originalen Klemme.

Aus der Klemme benötigt man den Gummischoner, den Bolzen vom Hebel und eines der Metallplättchen.

Schoner und Plättchen werden oben und hinten am Druckteil angebracht/versenkt und mit dem Bolzen verbindet man Körper und Hebel.

Die Bohrung für den Bolzen endet im Teil, um beim Positionieren zu helfen.

Das Spiel zwischen den Teilen absichtlich möglichst gering.

Das Metallplättchen und der Bolzen dürfen ohnehin möglichst eng sitzen.

Beim Durchgangsloch für die Strebe weiß ich nicht, ob es tatsächlich so eng ist oder ob Stützstruktur im Teil übrig blieb.

Es sitzt eng und das ist mir lieber als eine dauernd herunterfallende Klemme.

Ich habe alles montiert und nach ca. einem Tag konnte der Kunststoff so weit kriechen, dass ich es absolut in Ordnung finde wie es sich bewegt.

Da ich nur die eine Klammer habe, freue ich mich natürlich über Rückmeldungen, ob der Reparatursatz auch in anderen Fällen passt.

So weit hilft es hoffentlich dem ein oder anderen aus. :-)

 

 

Print Settings

Printer Brand:

Anycubic

Printer: 

All-metal Mega

Rafts:

Yes

Supports: 

Yes

Resolution:

0.15

Infill: 

30 %

Filament: Das Filament PLA White


 

Notes:

 

I printed both parts simultaneously therefore I put them on a raft. I guess you can print without if the lever goes on it's own.

 

 

 

Category: Replacement Parts

Tagi