Maltese Falcon - Full Size
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,11 € – 0,13 € netto (bez VAT)
Dla pliku: test-pinbbx2_02mm_pla_mk3s_8m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,12 € netto (środek widełek).
- Masa podana przez autora
- 1 g
- Czas druku podany przez autora
- 8,4 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Detective Tom Polhaus: "Heavy. What is it?" Sam Spade: "The, uh, stuff that dreams are made of."
- Ocena
- 5 / 5
- Polubienia
- 41
- Pobrania
- 348
- Wydruki
- 2
- Wyświetlenia
- 3314
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Sculptures
- Licencja
- Creative Commons — Public Domain
Detective Tom Polhaus: "Heavy. What is it?"
Sam Spade: "The, uh, stuff that dreams are made of."
Update Jan.21, 2012 : Added the full size STEP file (unmodified - one piece) for anyone who want to play around with it.
The Maltese Falcon is a great movie - you should watch it. Seriously - go watch it NOW!
My printer does not have the build volume to be able to print this full size in one piece, so I sliced it into four pieces in CAD, partially hollowed out each piece to reduce filament usage, and added dowel pin holes in all pieces to help align them for re-assembly.
The four pieces (from the head down) are as follows :
Filament Cost Print
Part Used (g) US$ Time
====== ======== ====== =======
Head 115 $2.92 9h39m
Chest 129 $3.28 9h08m
Feet 130 $3.32 13h27m
Base 113 $2.60 7h46m
Totals 487 $12.12 40h0m
In addition to the four falcon sections, I also included a print for dowel pins (or you can use 1/4" (6mm) wood dowels). The "hollows" in each section interconnect in the assembled piece; I plan to fill the inside with cement to give the model some heft.
Attribution : I found this STL by Colin Freeman:
https://www.thingiverse.com/thing:46631
I used FreeCAD to convert the STL to a solid, then imported it into OnShape and scaled it up to 12" in height.
The OnShape 3D CAD files for this are here :
Print instructions
Print in PLA using the 3mf files provided; otherwise :
- perimeters = 3
- 10% - 15% rectilinear infill
- detachable supports
Supports required for the sections are as follows :
- head : under the beak
- chest : none required
- feet : under the front claws, and two small areas on the sides
- base : print upside down, no supports
For the dowel halves, I increased elephant's foot compensation to 0.4mm. I have also included a test block for testing the dowel fit - the dowels should fit firmly but not so tight that it is difficult to insert or remove them. It is not necessary to glue the dowel halves together - simply hold the two halves together while inserting.
Six dowels are needed to align the pieces for assembly. I printed the dowels in halves - this enables better bed adhesion and allows the dowels to be printed linearly for greater strength. The provided gcode will print all 12 required halves individually in one session.