1 / 5
Wali Arm Monitor mount to wire shelf conversion — zdjęcie 1
1 / 5

Wali Arm Monitor mount to wire shelf conversion

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Insert for monitor mount to use with rolling wire shelf unit. WALI Dual Monitor Mount

Ocena
0 / 5
Polubienia
5
Pobrania
25
Wydruki
0
Wyświetlenia
707
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution

Disclaimer, I am not responsible for you printing this, using this and breaking your own monitors. I have been using this solidly for a month on 100 percent infill printed with ABS on a .8 nozzle. If you do use this file I highly recommend (but am not responsible for) that you test on your wire rack prior to adding your monitor. My dimensions and wali mount may be slightly different than yours.The initial fit was really snug on my mount and I did scratch the mount metal a bit trying to get the first protypes in and out. Which was fine for me because I was dedicated to my pursuit of this setup and was not going to return this item as I had already hand planed and finished walnut wood floor boards for the counter top and spent hours trying to figure out how to get a custom open large keyboard setup underneath. I am super happy with it, but I wouldn't recommend this for someone who has no diy experience. I did readjust the size in prusa slicer. I did end up sanding off the locking clips down quite a bit.

So I wanted to mount my monitors to the desk I made out of a rolling shelf instead of having to deal with having anything on my counter and worrying about it falling over. This was made specific to my own dimensions so you may need to adjust. I included files that can be adjusted right in prusa slicer with the right know how (cutting into parts can also be used and then enlarging z on certain areas. You will need to use the manipulation table and use object to move the items to get exact placements (don't forget to unlock to change height but not width or length). I printed with a .8 nozzle and 100% infill for stength.

The neg volume can be adjusted for a bigger inner diameter. You will only see the change when sliced.

I also included the plasticity file and the step file from plasticity but noticed that the files aren't to scale so had to do that in prusa slicer. I was just trying out plasticity on the free trial. My go to modeling has been a blender/prusa slicer fusion so far and is still my preferred method.

The mount I used was the WALI Dual Monitor Mount with Adjustable Gas Spring Arms Mount for 2 Monitors up to 32 inch. Each arm is supposed to hold up to 17.6lbs when used as is, I am not sure if the print changes the weight capacity. The model was GSDM002

I used ABS. Not sure how well PLA or PETG would work. 

Print Settings

Printer Brand:

Prusa

Printer: 

I3 MK3S

IMPORTANT NOTE

THIS IS A FUNCTIONAL PIECE. Please print this on a slower speed as higher speeds may make for a weaker print as this will be under constant pressure. 

Supports: 

Yes

Infill:

100% area will be tightened and under pressure, don't recommend using anything but 100 percent infill and largest nozzle size available to you. 

Filament:

I used ABS (but probably could use something else, test first though!)) 

 

Other Notes:

This was the mount I bought but could probably use with others. Also from the pictures my mount was different from the pictures some of the others posted, so you will most likely need to alter my files to work for your situation. WALI Dual Monitor Mount, Adjustable Gas Spring Arms Mount for 2 Monitors up to 32 inch, 17.6lbs Weight Capacity, Fully Adjustable for Home Office (GSDM002), Black
 

 

 

Category: DIY

Tagi