1 / 6
Makita 18V Battery Powered Solder Fume Extractor — zdjęcie 1
1 / 6

Makita 18V Battery Powered Solder Fume Extractor

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Makita powered fume extractor. Remix of lewosh's excellent model, side clips by Regis and Makita adapter by Wiseone.

Ocena
0 / 5
Polubienia
34
Pobrania
107
Wydruki
0
Wyświetlenia
1726
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

A modification of lewosh's excellent model with the following changes:

  • Added screw holes to mount the PWM controller.
  • Added mounts for a Makita 18V battery holder.
    • Also made the model taller to fit.
  • Added mounts for an adjustable power supply (to convert 18-20V battery to 12VDC).
  • Added hole for fuseholder to fuse battery 18V.
  • Removed front panel support material, printed with slicer supports only.
    • (This is a bit hacky but it was for me - I had difficulty cutting the default supports and still having the front plate fit, so I removed the modeled supports and used slicer supports)
  • Added a bottom cover cutout to make removing the battery easier.
  • The side-plates were added because they hold the fan shroud together much better than the original snap fit.

Printing Instructions:

  • Ensure supports are enabled for the base part (see images).

Assembly Instructions:

  • Refer to original post by lewosh for assembly information. In addition:
    • I snapped the front plate into place and used epoxy to secure it positively. Don't be surprised if the front bows or warps a bit during printing and needs some glue to hold the front plate.
  • Install M3 heat-set brass inserts for the battery and power supply board. Bottom cover holes use M4 inserts.
    • Note: Heat set bores are 3.8mm for M3 inserts and 5.3mm for M4 inserts (adjust if your brass inserts need a different bore).
  • Snap the Makita 643852-2 Battery Terminal (or knock off part) into the battery holder and mount to the base with M3x12 countersunk screws. 
  • Mounts for the buck converter (M3 heat set) and PWM board (M3 through-hole) are provided.
  • No wiring instructions are provided.

Special Notes:

  • The power supply board was tested and held constant 11.9 - 12.1 V at full load for a supply voltage of 14V-36V.
    • Adjust the maximum current potentiometer to current limit any overcurrent faults on 12V system. I adjusted mine to supply a maximum of 0.5A @ 12VDC.
  • The fuseholder protects the 18V battery against overcurrents, I installed a 0.5A fuse.
  • Use a DPST switch to break the 18V and 12V circuits simultaneously. This allows you to leave the battery inserted without draining via the 18V converter, and also to feed directly via 12V.
  • The 12V jack can be used to supply with 12V directly (ie: if no battery is available). Use a 2-pin jack and never connect both supplies simultaneously, or use a 3-pin jack (as I have) and use one of the pins to break the 18V circuit as the 12V barrel is inserted.

Room for Improvement:

  • The height of the overall unit makes the fan location less suitable for pulling fumes from the table surface, but works very well for a panavise or similar situation. A possible remix or improvement would add a second arm of articulation to allow the fan to pivot down to table height.
  • The bottom cover / battery tray leaves some wiring exposed. I didn't make any effort to enclose the battery.

Parts List:

Tagi