Enclosure for FLsun Q5
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Models to create side panels to enclose an Flsun Q5 printer and allow printing ASA and ABS
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 61
- Wydruki
- 0
- Wyświetlenia
- 1019
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
I wanted to be able to print ASA without warping. This design involves curved top and bottom parts that can be joined with 10mm aluminium tube creating a frame that can be covered with a sheet of thin polycarbonate or some other flexible material. I ordered a PVC table protector which is around 3mm thick and fixed it onto the frame with double sided tape.
Sorry about the messy photos! I wanted to get this done and didn't have time to clean up for the photos!

NOTE: I created these just for myself, so the models aren't defined with publishing in mind. The jigsaw curves are different in each component, so they're not interchangable. I would like to re-do the models, but not sure when I'll get the chance.
ANOTHER NOTE: I installed an OMG extruder which is significantly thinner than the original. I'll try to create an alternative model to accommodate the original extruder, but I've thrown out the original, so don't have the measurements. I also suspect that the original stands out further from the case that the parts I've designed, so may have to create deeper parts to allow for that.

Each top or bottom is created into multiple parts (either 2 or 3) that fit together so that the long parts can be printed on the Q5 itself.

The curved top and bottom ensures that the PVC doesn't interfere with the effector without being bulky.

I added recesses in the sides facing the printer housing to accommodate 6x3mm neodymium magnets which are sufficient to hold the frames against the printer. Finally, I allowed some overlap of the PVC from adjacent sides so that I could use magnetic tape on both sides to hold the sides together.
Overall this works very well. Whilst there are some gaps at the top, I can print ASA with no warping problems without having to block those gaps. Here's an example of Voron Z drive housing parts printed with Polymaker PolyLite ASA.

Even without a brim the left hand part printed virtually perfectly (one at 260 degrees hotend temp and 105 degrees bed temp (using all bimetal heat break and Foxies Marlin to achieve higher temps). There was one hardly noticable lift of one corner shown here.

With a brim the right hand part printed perfectly with no warping at all.
Finally, I haven't blocked the perforated bottom of the upper housing or the gaps around the motors, so the heated air is able to enter the housing and could potentially impact on the electronics and motors. I haven't seen any issues so far, however I am think about how to isolate the electronics and motors from the warm printing chamber and add better cooling. I'll add those components here if I get to that point.
Instructions
I used PETG for my prints - I haven't measured the chamber temperature while printing and I haven't tested with PLA so if you choose to go that path YMMV.
- Print 3 sets of the plain parts (1 & 2) - this gives you the bottom for the power side and the top and bottom for the display side.
- Print 1 set of parts for the top power side (1 & 2) which allows for the power socket mount.
- Print 1 set of parts for the top extruder side (1, 2 & 3) which allows for the extruder. NOTE, this part is designed for the OMG extruder, NOT the standard extruder. I will create parts for the standard extruder when I get the chance.
- Print 1 set of parts for the bottom extruder side (1 & 2) which allows for the bed heater cables to pass under the panel. I've uploaded the one I used, but it doesn't have the recesses for the magnets - I'll update that when I can. I haven't found that to be a problem as the bed heater cable holds the panel in place anyway.
- Source 6x500mm long 10mm OD aluminium tube. In Australia Bunnings stock this in 1m lengths. These should be a nice tight fit in the holes depending on how well your printer is setup.
- Source some PVC sheet or whatever you want to cover the panels with. I bought PVC dining table covers from Amazon, but I was also looking at 1mm polycarbonate sheets (A2 sheets would be large enough) - I may still switch to these, but it all works so I'm not in a hurry.
- Cut the sheets to size and stick to the assembled panels with double sided tape (or however you feel like it). I left enough overhang on the side so that adjacent panels could be ‘joined’ to complete the enclosure using magnetic tape on the PVC. If you use polycarbonate panels you'll need to think up a different way to cover the gap on the corners.
- Source some 6x3mm neodymium magnets to push into the sides which will hold them in place.