Gold Series Leadscrew guides for use with VenterMechs on Rat Rig V-Core 3
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Leadscrew guides for use with VenterMechs, wobbe rings (and now Oldham) style de-couplers in your bed arms on a Rat Rig
- Ocena
- 0 / 5
- Polubienia
- 12
- Pobrania
- 58
- Wydruki
- 0
- Wyświetlenia
- 480
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Please note my newer style ones for mounting in V-Core 3.1 stylised holders can be found here: https://www.printables.com/model/1552963-wiggle-woggles-for-lead-screw-guides-for-all-rat-r
Leadscrew guides compliment VenterMechs, Wobb e rings or the later style Oldham de-couplers in your bed arms on a Rat Rig V-Core 3 and Rat Rig V-Core 3.1 printer to eliminate leadscrew induced artifacts in your prints.
Please note these are guides not constraints!
These use printable wiggle woggles to allow some small movement of the leadscrews, instead of bearings which can over-constrain you lead screws even with the use of decouplers in your bed arms.
Over constraining leadscrews is not best engineering practice and can increase Z artifacts in your prints.
In addition using bearings will also cause excess resonances and introduce unpleasant noise to your printer.
For more info on VenterMechs please see http://www.bit.ly/VenterMech
Use the Rear central leadscrew guide for a V-Core 3.1
Use the Rear offset leadscrew guide for a V-Core 3
The front guides are compatible with both the V-Core 3 and 3.1
These are a two part design consisting of the holder and a printable Wiggle-Woggle.
There are two options for the Wiggle-Woggles.
Spiral Wiggle-Woggles - print from PETG.
The Wiggle woggle inserts from the bottom of the arms. Too fit tightly wind the spiral and fit in place. On the bottom of the holders you will note a tiny gap in the retaining ring this allows you to use a tiny screw driver to ensure the end of the spiral notches behind it's abutment. These should be printed with a 0.4 mm nozzle and 0.2 mm layer height.
TPU Wiggle-Woggles - print from Ninjaflex 85A Shore hardness TPU.
I prefer these ones. I would not recommend printing them out of a stiffer TPU. If you can't lay your hands on some 95A TPU then print the spiral ones above from PETG. These should be printed with a 0.4 mm nozzle and 0.2 mm layer height.
Install the front guides with the flats side facing down.
For faster printing the holders can be printed with a 0.6 mm nozzle and 0.3 mm layer height.
Coffee fund
If decide to make a donation to my coffee fund (which keeps me up late at night doing more of this stuff) I would appreciate it. There is absolutely no obligation for you to do this. My PayPal account is [email protected]
Please remember to post feed back as it is always valuable to me for future iterations.
Many thanks.
Liam Venter
MFBS Design
Updates
Update 11/03/22
The latest version (V3) of the rear guide provides more clearance between the top of the rear bed arm and the bottom of the guide.
Update 19/03/22
I have added a central rear leadscrew guide option, for hose who have centralised the rear stepper motor and leadscrew.
Print Settings
Printer:
Rat Rig V-Core 3 & 3.1
Rafts:
No
Supports:
No
Resolution:
0.2 mm with 4 mm nozzle
Infill:
30% Gyroid holders, 100% infill Wiggle-Woggles
Filament:
Any PETG or ABS. Do not use nylon for the Wiggle Woggles
Notes:
You may need an outer brim to print the spiral version of the Wiggle-Woggles depending on how good your bed adhesion is.
Category: 3D Printer Accessories