1 / 4
Gold Series XY joiners with clamping mod for Rat Rig V-Core 3/3.1 printers. — zdjęcie 1
1 / 4

Gold Series XY joiners with clamping mod for Rat Rig V-Core 3/3.1 printers.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Improved Rat Rig V-Core 3, XY joiners. (See my 3.1 versions for V-Core 3.1 printers) Note this mod is only relevant to…

Ocena
0 / 5
Polubienia
7
Pobrania
24
Wydruki
0
Wyświetlenia
287
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

Improved Rat Rig V-Core 3, XY joiners. (See my 3.1 versions for V-Core 3.1 printers)

Note this mod is only relevant to Rat Rig V-Core 3, Version 3.0 builds. Hole centres for the bearings on the XY gantry have changed with Rat Rigs version 3.1 update and with bearing stacks instead of idlers in 3.1.

The standard joiners use the bolts that act as the axles for the idlers to also clamp the XY joiners to the steel plate underneath attached to the linear rail carriage.

If you clamp the bolts up hard enough to have a secure connection to the steel plate you end up crushing the compressible tubes between the bearings in the idlers....which is sub optimal and will lead to early bearing failure. The bearings are not designed to be loaded in this direction.

This mod uses the cap screws that hold the aluminium extrusion into the printed XY joiners to also clamp the XY assembly to the aluminium plates.

These XY joiners also have the front overhangs removed for a cleaner look. This makes them easier to print standing vertically. I like to print these vertically to get a flatter/truer base and more perfectly aligned axle holes

This also gives them more clearance to the top plates of the front idler tensioners if your are using them with the OneBox OpenFront design, which is nice to have.

BOM

These original 10mm long cap head screws need to be replaced by 25mm cap head screws.

Coffee fund
If decide to make a donation to my coffee fund (which keeps me up late at night doing more of this stuff) I would appreciate it. There is absolutely no obligation for you to do this. My PayPal account is [email protected]

Please remember to post feed back as it is always valuable to me for future iterations.

Many thanks.
Liam Venter
MFBS Design

Attribution:

These are a derivative of the Original Rat Rig V-Core 3 XY joiners.

Updates

V2: 01/April/22. These now have slightly modified contours to prevent them hitting the front idler tensioners on the Gold Series OpenFront design

V3: 22/09/2022. Cleaned up aesthetics of design and made them easier to print than standard Rat Rig XY joiners.

V4: 16/01/23. Increased diameter of cutouts to give more clearance for the belts and rear idler flanges.

Print Settings

Printer:

OneBox

Infill: 

30%

Filament: Any PETG, ABS, ePA6-CF 
 

Notes:

 

To use. you will need two longer cap screws (5mm diameter x 25mm length)at the bottom on each side. These replace the two shorter ones that do not pass through the steel plate with the standard design.

Insert the two longer screws through the steel plate and use the tension on these to provide the clamping force between the new printed part and the steel plate.

Now you can set the tension on the bolts that pass thru the idlers. This tension should be just enough so that you can still freely spin the two plane idler spacers but are not loading the bearings in the idlers.

 

Category: 3D Printer Parts

Tagi