1 / 8
Soda Bottle Media Blaster Adapter — zdjęcie 1
1 / 8

Soda Bottle Media Blaster Adapter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This device allows you to make a low cost media blaster out of a soda bottle and an inexpensive air gun.

Ocena
0 / 5
Polubienia
12
Pobrania
133
Wydruki
0
Wyświetlenia
1081
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

This model allows you to make a low cost media blaster out of a soda bottle and an inexpensive air gun. The print results in a sturdy block that can be used to make a great little media blaster for very small jobs and occasional use. ALWAYS use safe practices when making and using air powered equipment. Media blasting is a very dangerous process. Make sure you know how to do it safely before you try it. When using the blaster start with the lowest possible air pressure and work your way up to a pressure that works for you. Too much pressure will cause this device to fail and may result in injury. ALWAYS wear adequate protective equipment when making and using a device like this.

Here are some links to short YouTube videos showing the blaster in action:

Rust Removal - https://youtu.be/w3Rh8ReXwTY

Paint Removal - https://youtu.be/kQEELNxc--s

(NOTE: I recommend using fine walnut shell media rather than sand or other blasting media. Sand will quickly wear out the air gun. Media blasting guns generally use ceramic or other hardened nozzles. The cheap air gun this is made of uses fairly soft metal that will wear out quickly when using sand.)

Print Settings

Printer Brand:

Prusa

Printer: 

I3 MK3S

Rafts:

No

Supports: 

No

Resolution:

0.2mm

Infill: 

15%

Filament: Overture PLA Gray


 

Notes:

 

This design specifically uses shapes that eliminate the need for supports when printed in the default position.

Post-Printing =============

Assembly and Customizing

See the accompanying photos for assembly illustration.

The long narrow hole is meant to hold the extended nozzle of a cheap air gun. The 5.1mm diameter hole snugly fits the nozzle of an air gun I got from Harbor Freight (Link below). I wanted the fit to be snug so the soda bottle full of blasting media would be held securely upright.

The wide hole fits a typical soda bottle lid in the US. The nozzle tube will be exposed in the bottom of the wide hole once it is inserted through the long narrow hole. I used a rotary tool to grind away the exposed part of the nozzle tube so blast media can enter it from the bottle.

Cut a hole in the bottle lid to allow the blast media to flow out. Make sure to glue the lid securely in place before use or the bottle will blow off as soon as you apply pressure. I used a liberal amount of CA glue to hold the lid and form seal around it. If you find that your glue does not hold the lid securely enough you might want to drill a hole from one or both sides and use screws to hold the lid and bottle in place. (NOTE: For me, the reason for this design was in the lack of the need for drilling and screws. Making a quick bottle change possible. For you, another design might work better. There are a couple of good looking ones on Thingiverse. I haven't made them so I can't vouch for their usefulness.)

I use fine walnut shell media rather than sand or other blasting media that will more quickly destroy the air gun. Media blasting guns generally use ceramic or other hardened nozzles. The cheap air gun this is made of uses fairly soft metal that will wear out quickly when using sand. Walnut media will easily remove paint and light rust and skin if you are not careful.

Harbor Freight Air Gun https://www.harborfreight.com/air-tools-compressors/air-compressor-accessories/air-blow-gun-set-64149.html

 

Category: DIY

Tagi