Sordin Supreme Pro-X Battery Tool
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,25 € – 0,31 € netto (bez VAT)
Dla pliku: SupremeProXBatteryTool_0.25n_0.12mm_PLA_MK4IS_21m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,28 € netto (środek widełek).
- Masa podana przez autora
- 2 g
- Czas druku podany przez autora
- 21 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
A simple tool to aid in the removal and installation of the lower AAA battery in the Sordin Supreme Pro-X earmuffs.
- Ocena
- 5 / 5
- Polubienia
- 12
- Pobrania
- 210
- Wydruki
- 4
- Wyświetlenia
- 1076
- Oceny
- 5
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A tool to aid in the installation and removal of the lower AAA battery in a pair of Sordin (formerly MSA) Supreme Pro-X electronic earmuffs. If you own a pair of these, you know how annoying it is to change the batteries because of the design of the battery compartment. If you're like me, you prefer not to vigorously beat your expensive earmuffs against your hand to get the battery out. For this reason, I designed this tool to aid in the removal and installation of that pesky lower battery.
Printing:
- The battery tool MUST be printed with a 0.25mm nozzle (I tried 0.4mm and the head of the tool was just too weak; seems counterintuitive, but there's only a single perimeter at the tip of the U-shaped head of the tool when printed with a 0.4mm nozzle, which results in this area being weak and breaking off with only a small force applied).
- .0.1-0.12mm layer height is strongly recommended.
- At least 1mm top/bottom thickness.
- Minimum 3 perimeters.
- Minimum 25% infill density.
- PLA recommended for rigidity.
Use:
Lower battery removal:
Holding the earmuffs upright, slide the tool in through the battery compartment opening until the head of the tool drops down between the battery housing and the battery (the toolhead should index perfectly on the front of the battery). Apply some rearward pressure to the front of the battery while simultaneously lifting the tool upward. This should raise the front of the battery. Once the positive (+) terminal on the battery has cleared the lip of the battery housing tunnel, you should be able to flip the earmuffs upside down and the battery should fall out.
Lower battery installation:
The process to install a new battery is nearly identical to the removal of the old battery in reverse, except when inserting the new battery, hold the earmuffs upright but with a slight angle, so the rear of the battery compartment is lower than the front of the battery compartment (as you're viewing it). This will entice the negative (-) end of the new battery to drop down before the positive (+) end, allowing you to place the tool on the front (+ end) of the battery and, while applying a little rearward pressure, push the battery down into the lower socket. If you can't get the front of the battery all the way down in one go, you can place the toolhead on the side of the battery and push it down the rest of the way once the positive (+) terminal is seated below the lip of the battery compartment tunnel.