1 / 4
MPCNC 525 Laser Holder for 2.8W laser w/ fan and line lasers — zdjęcie 1
1 / 4

MPCNC 525 Laser Holder for 2.8W laser w/ fan and line lasers

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a MPCNC 525 mount for the JTech 2.8 Watt laser Some new additions in the new version are a block to hold a…

Ocena
0 / 5
Polubienia
0
Pobrania
11
Wydruki
0
Wyświetlenia
163
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution

This is a MPCNC 525 mount for the JTech 2.8 Watt laser

Some new additions in the new version are a block to hold a loc-line hose for air assist, and a post to hold a #6 screw that could be used with a touch Z-probe.

I used brand name loc-line hose, knock-offs seem to be slightly different dimensions and you may be able to get them to fit. I'm still testing the right combination of loc-line for great cuts, but air assist is a huge improvement over not having any. For the air source I got a fish tank air pump, the one with the most pressure I could find, 0.035Mpa, it seems to have plenty of pressure and not super noisy.

Sourcing a long enough #6 screw for the touch probe was a bit more of a challenge than I expected, I finally found some 4" long ones on amazon. While a touch probe is not necessary, It allows me to be a bit lazy when swapping out material and I needed something long so the air assist nozzles wouldn't be in the way.

There is a split in the block to allow you to route the cable to the laser through without having to disassemble the laser module or fish feet of cable through.

It also includes nut-traps on the back to hold the laser, the nut-traps are deep enough to accommodate #6 nylon stop nuts. The nut-traps are very snug, you may have to pull them in without the laser in place first.

Print Settings

Printer Brand:

Prusa

Printer:

i3 MK2S

Rafts:

No

Supports:

No

Resolution:

0.2 mm

Infill:

50%

Additional Materials

Additional Materials

(2) #6-32 x 3/4 to mount the laser
(2) #6-32 Nylon Stop Nut to mount the laser

(4) #6-32 x 3/4 to mount the cooling fan

(4) #6-32 Nylon Stop Nut to mount the cooling fan

(4) #6-32 x 3/4 to mount the tool block

(4) #6-32 Nylon Stop Nut to mount the tool block

(4) #6-32 x 3/4 to hold loc-line

(4) #6-32 Nylon Stop Nut to hold loc-line

(2) line lasers https://www.amazon.com/WayinTop-Adjustable-Positioning-Sighting-Telescope/dp/B07ZNKTCLQ

The line lasers are a press fit and require no hardware. If it's too tight, use a straight screw driver and gently pry the split apart a little for assembly and fine alignment. If they are too loose, a layer of painters tape on the diode works

Loc-line set https://www.amazon.com/gp/product/B006R9O3HE

Air Pump https://www.amazon.com/gp/product/B07428YHG7

(1) #6 x 4" screw for touch probe, optional and requires a touch probe be setup on your CNC

Category: Parts

Tagi