Tronxy XY-2 Pro Dual Z-Axis Upgrade
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
For adding a second lead screw and motor to the Tronxy XY-2 Pro 3D printer.
- Ocena
- 0 / 5
- Polubienia
- 10
- Pobrania
- 101
- Wydruki
- 0
- Wyświetlenia
- 1066
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
UPDATE 09102025: I added a version 2.5 for the carrier bracket. JDS noted that the throughway hole for the brass nut on my Ender 3 dual Z axis upgrade is too small to fit anti-backlash nuts. JDS mentioned that he may remix the Ender 3 carrier for anti-backlash nuts so I'm leaving that model as is for now, but opened up that hole from 11mm to 14mm on both left and right carriers for my Tronxy design. Note that the version 2.5 bracket differs in appearance from the version 2 file as I made other changes for clearance of the taller stepper motor I have on my Tronxy as part of my “X Axis Rework for Tronxy XY-2 Pro”.
UPDATE 12152024: I did just add a Version 2 of the bracket part that uses the flat sided Creality style brass nuts with tapped screw holes, so be careful which version you're downloading and printing. Make sure the nut cut-out on the top face matches the brass nut you intend to use with this kit.
I'll begin by saying that it may not be especially cost effective to add a second lead screw without a purchased kit unless you just happen to have a spare 400mm lead screw, stepper motor, coupler, brass nut, and additional metric hardware for doing so. This model does however correct a problem inherent to Tronxy's original design.
As for the 28mm spacer, I'm using a M4 x 40mm screw with both a split and flat washer for maintaining tension without cutting into the plastic plate and a M4 T-nut.
The cut version of mknets motor mount can be used on either side of the machine now with T-nuts.
The brass nut I'm using for the 2nd lead screw is an Anet style round 4 hole nut, which is what Egco intended for his original design, simply because those are what I have handy. The Creality style nuts with two flat sides will not directly fit this model. Without taking one of my machines apart that uses the Creality style nuts, I'm unable to take proper measurements. If there is any interest in using the other style brass nut with this design, drop a comment and I'll revisit this design adding a second version of that part that accepts those nuts.
I've not seen dual leadscrew kits designed specifically for the Tronxy XY-2 Pro, but many people are using Ender 3 kits. The Ender 3 kits only work because the Tronxy has the same design flaws as the Ender 3 from which Tronxy took all their design ques from. The screw for the roller on the inside should NOT go from the front plate to the rear plate. That feeble design causes the pom wheel to cock diagonally when adjusting the cam nut to adjust tension. The original 30mm screw that held the inside pom wheel should be used. And while you've got things mostly apart, the left side has the same design flaw, so I'd recommend replacing that 40mm screw with a 30mm screw and discarding the spacer. That roller will mount with the cam nut to the rear plate on the left side, unlike the right side where the camnut installs to the front plate. I've included photo's of both sides from the best angles I could get for the changes I recommend for both adjustable pom rollers.
I print all these parts as oriented in the STL with 100% infill and use supports only on the motor mount.