1 / 37
Sixpack Bierträger zur individuellen Gestaltung - Six-pack beer carrier for individual design — zdjęcie 1
1 / 37

Sixpack Bierträger zur individuellen Gestaltung - Six-pack beer carrier for individual design

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Bierträger designt für 0.5l NRW Flaschen mit Logos zum einkleben. Beer carrier for NRW bottles with logos to glue in.

Ocena
5 / 5
Polubienia
130
Pobrania
1194
Wydruki
15
Wyświetlenia
5262
Oceny
12

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Description in English below

Update 20.06.25

Kiste ohne Ausnehmungen hinzugefügt

Update 08.05.25

Wieselburger Logos hinzugefügt

Update 07.04.25

Griffe und Stopper für Montage mit Zylinderkopfschrauben M3x14 oder M3x15 Zylinderkopfschrauben und Heat Set Inserts M3x5x4 (Voron) hinzugefügt

Update 05.04.25

Logocutouts der Kiste abermals ein wenig vergrössert

Update 05.02.25

Murauer Logos hinzugefügt

Update 15.01.25

Zwettler Logos hinzugefügt

Update 17.12.24

mir ist aufgefallen, dass die Toleranzen für die Ausschnitte der Logos je nach Druckerkalibrierung verwendeter Düse etc. manchmal zu eng sind.

Daher lade ich die Kiste nochmal mit angepassten vergrösserten Logoausnehmungen hoch.
 

Update 11.06.24

Zipfer Logos hinzugefügt.

Update 27.03.24

kürzere Griffe (L248mm) passend für Prusa MK Bett hinzugefügt.

Update 18.02.24

 Hirter & Budweiser(Czech) Logos hinzugefügt

Sixpack Bierträger zur individuellen Gestaltung  

Stützen nur unter den 4 Kistengriffen  notwendig- ich habe die Aufmalstützen vom Prusaslicer verwendet.

Druckt die Kiste/Griffe und Stopper abhängig von der Nutzung so stabil als möglich/nötig, immerhin kommen bei voller Befüllung rund 5,3kg Belastung drauf. Vor allem beim Griff+Stoppern viele Perimeter und hohes Infill verwenden.

Griffe und Stopper werden nach dem einfädeln verschraubt oder sicher verstiftet (hierfür kann zb. ein entsprechender Nagel mit einem Lötkolben eingeschmolzen werden)

Tip: druckt vorab eine Miniatur der Kiste (zum Beispiel 33%) mit dem selben Material und den Druckeinstellungen, die ihr für den Druck der vollen Größe verwenden würdet, das braucht nicht viel Zeit und Material, und ihr könnt mögliche Probleme bezüglich   
Layerhaftung, Gesamtstabilität etc.
frühzeitig erkennen und korrigieren.

-----------------------------------------------------------------------------

Update 20.06.25

added crate without cutouts

Update 08.05.25

added Wieselburger Logos

Update 07.04.25

Handles and stoppers for mounting with cylinder head screws M3x14 or M3x15 cylinder head screws and Heat Set Inserts M3x5x4 (Voron) added

Update 05.04.25

Logo cut outs of the box again slightly enlarged

Update 05.02.25

added Murauer Logos

Update 15.01.25

added Zwettler Logos

Update 17.12.24

I noticed that the tolerances for the logo cutouts are sometimes too tight depending on the printer calibration, nozzle used, etc.

Therefore, I am uploading the crate again with adjusted, enlarged logo cutouts.

Update 11.06.24

added Zipfer Logos

Update 27.03.24

Added shorter handles (L248mm) suitable for Prusa MK bed

Update 18.02.2024

added Hirter & Budweiser(Czech) Logos 

Six-pack beer carrier for individual design

Supports only necessary under the 4 crate handles - I used the painting supports from the Prusaslicer.

Depending on the use, print the crate/handles and stoppers as stably as possible/necessary, after all, when fully filled they will have a load of around 5.3 kg. Use a lot of perimeters and high infill, especially for handles and stoppers.

Handles and stoppers are screwed or securely pinned after insert (for this purpose, for example, a short nail can be melted in with a soldering iron)

tip: pre-print a miniature of the crate (for example 33%) with the same material and print settings that you would use to print the full size, this does not take much time and material, and you can avoid possible problems regarding
Layer adhesion, overall stability etc.
detect and correct early.

Tagi