1 / 17
3 point bed holder for tehnologika.net y-carriage — zdjęcie 1
1 / 17

3 point bed holder for tehnologika.net y-carriage

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

3-point plate (hot bed, glass, alu plate...) holder for Y-carriage from:TEHNOLOGIKA why? - I'm not using the aluminium…

Ocena
0 / 5
Polubienia
1
Pobrania
11
Wydruki
0
Wyświetlenia
88
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

3-point plate (hot bed, glass, alu plate...) holder for Y-carriage from: TEHNOLOGIKA

why? - I'm not using the aluminium plate at all because have a piece of borosilicate glass that has heater glued directly on it so no screws in/trough glass/heater so something like this is required. As you can see in one of the pictures, you can use your original heated pcb bed (with or without glass on top of it) with this 3 point system too.

update 20170107:

  • shorter shaft so a thumbscrew can be used
  • seating for the spring
  • longer lip to hold narrower glass too
  • mount works great, fits perfectly, holds the bed nicely, no play!
  • the only thing left to test is how strong the ABS will be holding 110C bed inside 70C chamber

update 20170108:

  • added 3 new versions of bed piece, original one expect M4x5x5mm metal insert to be pushfitted into the hole on top so that M4 screw can be used to clamp the glass cap to the bed piece. Since not everyone have these metal inserts 3 other versions are added, one with a small 2mm hole that will properly hold a 3mm plastic (or wood) screw and a version with 3mm hole trough it and M3 nut holder on the bottom of the shaft so one can use M3 screw and nut to hold the glass cap and one with M4 hole and place for a trap M4 nut (probably best version if you are not using inserts)
  • added second glass cap with thicker end if you want to hold in bed something that's thinner then 4mm (like for e.g. 3mm plate)
  • tested the whole contraption in real life, no play, ABS is not deforming while heated bed is at 110C and chamber at 70C

update 20130309:

I was using 35mm M3 screws (to go trough "bed piece" and the bed) with round Socket Cap head and they tend to rotate inside the piece sometimes so bed leveling gets harder then it should so I found the hexagon head bolts M3x35mm on blej and redesigned the bed piece to take the hex head m3 there so it would not rotate :)

Print Settings

Printer:

self made

Rafts:

Doesn't Matter

Supports:

Yes

Resolution:

0.15-0.25

Infill:

50%

Notes:

The parts are strongest the way they are laid down in STL, unfortunately this means for the "8mm shaft" piece you need to use support.

I'm using ABS as material to print this, I'm pretty sure PLA will not work (as the parts will deform when bed goes over 60C), dunno how PC, HIPS or Nylon would perform

Post-Printing

  1. attach a "carriage piece" to your tehnologika bed so that the hole in the piece aligns with the hole in the bed
  2. add a spring over the hole (use the original springs that came with M150's bed), it should snap comfortably into the "seat" over the hole
  3. select your "bed piece" depending on how do you plan to attach glas cap to it, and place it in the carriage piece, the spring should seat in the bed piece too
  4. put the M3 screw, min length 25mm, max length 35mm (ideal 30mm) trough both pieces
  5. screw in the m3 on the bottom of the carriage piece (or use those thumb nuts that came with M150 or print one of the thumb nuts from the thingiverse)
  6. add a glass cap (if your bed is thicker then 4mm use flat glass cap piece, if your bed is 4mm or thinner use the "glass cap thinner bed" piece) and fasten to the bed piece using the selected way of fastening (if you are using metal insert use M4 screw, if you are using self tapping screws or m3 screw use those..), fasten loose so you can move the glass cap out of the way so you can put your bed in (and later tighten the cap)

repeat three times

Optionally, when everything is done, you can "fix" the M3 screw going trough everything. In this design I'm using "round" head seat for the M3 screws (cause I only have this type of M3's) and in this case only friction is holding the M3 screw from turning when you tighten/loosen the nut on the bottom. There's 2 way of fixing the M3 screw:

  • if your screw have threads all trough then you can just use a nut (ideally nyloc) and secure the M3 screw in place. The spring will go neatly over the nut so no worries there.
  • if your screw don't have threads all the way (most long one don't) then, what I did, is mix some ABS waste with some acetone to get a thick mixture (very thick, like paste / clay) and fill the top hole where the M3 head is completely while M3 head is in; leave for 24 hours to completely dry and solidify.. the M3 will be tightly secured and will not self rotate :D

Anyhow, even without "fixing" the M3 screw, you only need to hold it by hand while fastening the bottom nut for the first time, once you tighten the spring the friction will be enough to hold it in place and not allow it to rotate

How I Designed This

ONSHAPE

designed using onshape, source available here (if you create account on onshape you can also edit/copy/export the parts):

bed holder source on ONSHAPE

Category: 3D Printer Parts

Tagi