Fix ABL issues with MAXPROBE backplate - Fixes auto bed levelling issues for Sprite Extruder with CR Touch on Creality printers CR10 Smart Pro Ender 3 S1 - Zero Y 0 Y crtouch probe offset mount
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
1,36 € – 1,66 € netto (bez VAT)
Dla pliku: maxprobe-backplate-v1.0-petg.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 1,51 € netto (środek widełek).
- Masa podana przez autora
- 15 g
- Czas druku podany przez autora
- 1,75 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Fix auto bed levelling issues by relocating the CR-touch probe for 0 y-offset, while keeping x-offset close to standard
- Ocena
- 5 / 5
- Polubienia
- 41
- Wydruki
- 3
- Wyświetlenia
- 4000
- Oceny
- 4
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- Standard Digital File License
Sick of auto bed leveling issues? The MAXPROBE backplate fixes them for good. Your printer should have come from Creality like this.
Features
Easy to install - takes just 10 minutes, no cutting wires or soldering needed
Uses all original components and fasteners
Significantly improves bed probing accuracy
Reduces the unprobed bed area
Relocates CR touch probe for -34 X-offset and 0 Y-offset - this is the smallest x-offset of any zero Y-offset probe mount available - critical for minimising unprobed bed area
Retains the factory ability to easily remove and install the extruder
Clean look with wiring tucked away inside
Includes
STLs with different tolerances to suit your printer and settings
Step by step installation instructions (English)
Suits
Printers with Creality Sprite Pro extruder
Creality CR10 Smart Pro
Creality Ender 3 S1
Creality Ender 3 S1 Pro
Install notes
Need to trim 3mm off the CR-touch probe (see photo)
Two versions included:
Threaded insert version - uses 2x each M2, M2.5, M3 Aliexpress brass heat-set threaded inserts (recommended for long life)
No-insert version - has holes designed for the original fasteners to self-tap directly into the plastic
CR-10 Smart Pro needs to use a low-profile X-axis limit switch mount (available free in my other models)
Setup notes
You will need to update some of your printers settings with Pronterface:
PID retune the hot end. You can do this with the following commands:
- M303 E0 S240 U1
- M500Update XYZ probe offset. You can do this with the following commands:
- M851 X-34 Y0 Z-1.5
- M500
Then you need to adjust the Z height on your printer. Step 2 above sets it to -1.5 which is conservative. However, if this value is wrong your nozzle can hit and damage your bed, so you need to adjust to suit your own printer
Choosing the right STL
Due to the way FDM printers work, small holes will come out slightly undersize. Therefore, STLs with different size holes in them have been included. Choose the hole size that allows the spigot on the heat-set insert to sit in the hole before being installed. If you are not sure, start with the +0.3 STL.
Print settings
Material: PETG recommend
Layer height: 0.2
Walls: 1.6 thick (0.4 line width) , 1.5 thick (0.5 line width)
Top/bottom thickness: 1.6
Infill: 60% cubic subdivision
Supports: Not required