Age of empires II: Central european Fortified tower lamp
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Model kit of a desktop lamp in the shape of a Fortified tower of Central european architecture from Age of Empires 2
- Ocena
- 4 / 5
- Polubienia
- 20
- Pobrania
- 77
- Wydruki
- 1
- Wyświetlenia
- 818
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution — Share Alike
Warning: You’re being attacked by Henry the Lion!!!
First of all, don't get intimidated by the height of the model or the various colours. Although being close to 40 cm from ground to pinacle it is modelled in smaller pieces and everything was printed in a Prusa Mini+ so this should be printable in almost any printer higher than 180 mm with a single extruder and can be easily scaled upwards. The only extra hardware that is required in some of the parts if printing at original scale is a 0,25 mm nozzle (and maybe a hard 0,6 if you're going to filled materials as I did). A printer with a Revo hotend or another quickswap nozzle solution will make printing this kit much smoother.
The tower comes in a general STEP file if you need to inspect or modify anything. The STEP file for the shield hanging from the wall also comes as a blank template for you to create your own. The actual parts come in different folders according to the material the filament is imitating.
The Core and the Tube can be printed in regular black PLA as they are barely seen. The former hold the walls and a good part of the weight so consider a robust profile while the latter holds the bulb. It funnels at the top and both a dycroic bulb and a common E-11 holder fit there. It is ment to slide inside the core and has no mandatory orientation.
The ones from “clay” might be the trickiest. I originally went to FormFutura Terracota PLA but the tiles require a very precise detail that a 0,6 nozzle cannot produce and even with a 0,4 can be challenging. A 0,25 nozzle print all the roofs without any trouble whatsoever and my final choice for the fillament was Fillamentum CPE HG100 Caramel Brown Metallic.
The clock can only be printed with a 0,25 nozzle as the arms of the needle are a single line at times but being a mostly flat geometry didn't give any trouble. I wouldn't recommend crancking up the speed as the 12 total parts of the 4 clocks takes very short time even at 30 mm/s. These were printed in Fillamentum PLA Gold Happens.
The plaster parts can be printed in any white PLA, PETG or other common material with a milky white tone. Mostly any nozzle size will work with those parts.
The player colour are to represent the player owner in the game. The triangles slot between the wodden frames and the band arround the pinacle. The latter prints better at 0,25 nozzle. If you want to be faithful to the game the colours to go are: Blue, Red, Green, Yellow, Cian; Orange; Grey and Pink.
The pinacle is quite easy to print. I didn't fully understand what it is supposed to be made of but I'm guessing copper plates. I didn't have any filament tone that resembles that so I used Fillamentum PLA Vertigo Galaxy and give a slate tone.
The stone structures are probably the riskier to print if you're using actual stone fillament. The four walls are ment to be printed vertical and a variant of the 3mf file is attached with a rib on the arrow slots to make the overhang printable. They could also be printed flat but the sloppy section might not turn well. The rest of them should be a problem to print. I used FormFutura Granite PLA with a 0,6 ObXidian at 0,1 mm layer heigh (Any higher and the brick patern doesn't show). The pinacle was printed in Fillamentum PLA Turkey egg.
Finally the wooden parts are mostly flat. I ended splitting the frames arrown the battlements into 3 flat subframes as printing the slim structure vertically results in a flimsy part that is going to snap before gluing. The doors have iron hinges over them. I attached a file with the wood and iron separated in case you need. I used Fillamentum Timberfill Rosewood for all the timber and PLA Iron grey for the hinges.
In case you use any filled fillament remeber to properly dry it as the particles absorb a lot of moisture due too capillarity and causes ugly levels of thick stringing.
For the assembly I recommend superglue both in tipped and brush bottles and maybe another type that can thicken out and join two non fully paralel faces. Begin with assembling the clocks and gluing them to the walls and then these to the core. Each wall has a different pin so you place each of it in the correct location. Machicolations goes on top and then the hoardings. Both also have an assembly pin so you place them in the correct orientation. Then comes the windows, murder holes, battlements, floors and timberframes. Separatelly, assemble the roof with all the tile parts, arrowslits and pinacle and then rest it over the hoardings. I don’t recoment permanently gluing the roof just in case you need to access the interior.
The electrical wiring is quite straigh-forward. You’ll need a plug (doesn’t need grounding), 2 wire cord, a switch, a bulb holder and the actual bulb. The tower has a cutout at the back so the cord can enter freely and climb all the way to the bulb inside the tube.