1 / 5
Triple Relay Holder 4-Fuse Holder w/Wiring Box — zdjęcie 1
1 / 5

Triple Relay Holder 4-Fuse Holder w/Wiring Box

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A basic, yet elegant solution to installing up to 3 auto relays and 4 auto fuses to your next wiring project.

Ocena
0 / 5
Polubienia
7
Pobrania
92
Wydruki
0
Wyświetlenia
544
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
GNU General Public License v3.0

                                                     Print and Assembly Instructions:

Important: the wire channel used in this design is approximately ½" diameter and may not accomodate enough thick gauge wires (high current applications) for all the relay/fuse connections. Check your wire “bundle” overall diameter BEFORE starting this project!

Overall dimensions - assembled: H79.34mm X W115.26mm X D32.42mm

This is a variation of an original design of mine, for installing extra relays and fuses into any project. Because this isn't the final design I'm using for my project, I never printed it and therefore, can't provide actual photos - BUT I know the relay sockets fit standard 4- or 5-pin auto relays perfectly. To show proof of concept, I've included a couple pictures of an earlier version that I did print - before adding the additional upper section. I've since went on to further customize it to fit my specific needs, including raised mounting holes inside the enclosure for a module. This version however, is likely to serve a wider base of people that are searching for relay holders. The wiring box IS large enough to fit a bistable module, good for using a momentary button to execute on/off functions - which can be used to trigger a time delay-off circuit for accessories. All that's needed in this model is to add the mounting holes with a 2mm rise off the base to accomodate the circuit board's solder connections underneath. 

The upper and lower “socket” sections are separated from the base in order to allow for optimal orientation on the print bed, with the holes' inner dimensions in mind.

Without supports, print the upper (blue in pic) and lower (green in pic) sections that hold the relays/fuses with their faces oriented toward the print bed (small hole-side down). The curved wire chamber in the base (yellow in pic) should print fine without supports (inside to outside wall printing order) but the screw mounting tabs at the top of the box will need them (tree/organic recommended). The screw mounting tabs were left with a 90 degree plane on the bottom to more easily accomodate a module, should you choose to add the mounting holes in the bottom. The base CAN be printed completely support-free ONLY if you add some sloped faces under the screw mounting tabs - or extend the bottoms all the way down the to lower face. The lid (orange in pic) should be printed top-side (flat) down.

Once all parts are printed, place on a flat surface, apply glue to joining faces and slide together. To ensure upper walls of the base are aligned, screw the lid into place before the glue sets. To avoid glue from accidentally coming into contact with the lid, sandwich a piece of paper between it the sockets, and the base. Allow glue to cure before further handling.

Pass your non-terminated wires through the curved wire chamber. It's important they're inserted before terminating because the more wires you feed through the chamber, the less room you'll have for subsequent wires to fit and terminal connectors will need more room. Connect your wire ends intended for the relay/fuse slots to ¼" female spade terminal connectors with locking tab (see picture).

Looking at the front of the socket (small hole-side), you'll see a small slot centered in one face of each hole. This is the face the locking tab on the connector sits against. From the rear (large hole-side), insert your terminated wire into the corresponding relay/fuse holes of the upper and lower sections. Once fully inserted, the connector will ‘click’, locking into place. If the connector does not lock into place, confirm the orientation is correct and if necessary, bend the locking tab out slightly more then reinsert. If you find the need to remove the connectors after they're locked in, insert a small pin, (paper clip works well) into the front slot, and gently press the locking tab on the connector inward enough that it'll slide back out. After it's removed, you may have to use the paper clip to re-bend the connector's tab back outward slightly to get it to lock again.

The mounting holes are large enough to accomodate M4 bolts/screws (non-hex head). Alternatively, you can use 3M double-sided molding tape to mount it (clean both surfaces thoroughly with IPA to ensure maximum adhesion), removing the need to create holes in your mounting surface. The lid screw holes use M3-6 or longer sheet metal/wood screws - (don't use too long of screws as the tips will be exposed to your wires, potentially leading to damaged wire insulation). Larger diameter screws WILL cause the screw mounts to split! The screws will cut their own threads upon installation. Do NOT overtighten! Self-tapping screws may also work but will leave larger sharp edges below the screw mounts and increase the risk for damage to the wires.

Tagi