1 / 5
Reborn 2 TFT 4.3inch housing fits as the original — zdjęcie 1
1 / 5

Reborn 2 TFT 4.3inch housing fits as the original

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a printing frame for a 4.3" TFT touchdisplay (DSI LCD) for Raspberry Pi.

Ocena
5 / 5
Polubienia
9
Pobrania
39
Wydruki
1
Wyświetlenia
575
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Dieses ist ein Austauschmodell des originalen TFT Rahmens um statt nur 3inch eine 4,3inch Bildschirmgröße ohne Bearbeitung oder gar Austausch der Türen beim Flying Bear Reborn2 zu bekommen.

Ich habe einen günstigen Waveshare 4.3 inch DSI LCD direkt am Rpi4 angeschlossen und mit diesem Gehäuse an die originale Stelle montiert. Der Raspberry ist im Schacht unter dem Reborn2 mit eingebaut. Ich habe das originale Board behalten und auf den Raspberry per serial gebacht. Wifi läuft über den Pi.

Zur Befestigung des neuen DSI TFT im gedruckten Rahmen, hab ich einfach eine geometrische Figur als Rechteck mit 2mm Höhe auf das Druckbett erzeugt, die Maße hiervon sind 75mm x 8 mm. Das ganze 2 mal gedruckt, fertig.

Nach Augenmaß  Löcher in die Halter bohren (Rechtecke lassen sich prima auf Spannung über die Schraubsockel ziehen) so angezeichnet und mit einem 2,5 mm Bohrer die Löcher in die Klemmen gebohrt. Bei meinem TFT sind die Halter eher zum unteren Ende vom gedruckten Rahmen gelegen, das mag bei Anderen LCDs auch anders sein, daher keine Datei dazu.

Bilder vom befüllten Innenleben des Rahmens kann ich jetzt leider nicht liefern, da bereits alles verbaut war bevor ich auf die Idee kam das Projekt online zu stellen. Eventuell reiche ich das noch nach, ich muss noch mal an die Elektronik um 24 Volt für Beleuchtung abzugreifen.

Ich habe den Drucker auf CanBus umgerüstet, was auch gut funktioniert.
Das wird auch noch mal ein Beitrag, aber zu späterer Zeit

 

 

Thank you google for translation in english:

This is a replacement model of the original TFT frame to get a 4.3 inch screen size instead of just 3 inches without editing or even replacing the doors on the Flying Bear Reborn2.

I connected a cheap Waveshare 4.3 inch DSI LCD directly to the RPI4 and mounted it in the original location with this housing. The Raspberry is installed in the shaft under the Reborn2. I kept the original board and transferred it to the Raspberry via serial. Wifi runs through the Pi.

To attach the new DSI TFT to the printed frame, I simply created a geometric figure as a rectangle with a height of 2mm on the print bed, the dimensions of which are 75mm x 8mm. Printed the whole thing twice, done.

Drill holes in the holders by eye (rectangles can easily be pulled over the screw bases under tension) and then drill the holes in the terminals with a 2.5 mm drill. On my TFT the holders are located towards the lower end of the printed frame, this may be different for other LCDs, so no file for that.

Unfortunately, I can't provide pictures of the filled interior of the frame because everything was already installed before I had the idea to put the project online. Maybe I'll pass this on later, I have to go back to the electronics to get 24 volts for lighting.

I converted the printer to Canbus, which also works well.
That will be another post, but at a later time

 

 

Tagi