Cradle for FluidNC Dial Pendant on YZ plate of LowRider v3 CNC (v1.6)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The "No Magnets" edition - Cradle for FluidNC Dial Pendant on YZ plate of LowRider v3 CNC (v1.6)
- Ocena
- 0 / 5
- Polubienia
- 13
- Pobrania
- 92
- Wydruki
- 0
- Wyświetlenia
- 565
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- GNU General Public License v2.0
NOTE: There are now 3 editions of this (two with magnets, and a third without magnets):
- 1st edition - GET IT HERE - magnets on outsides, with opposing magnets touching
- 2nd edition - GET IT HERE - magnets on insides, with opposing magnets not touching
- 3rd edition - THIS LISTING - no magnets at all, just a press fit insertion & removal
Watch below to see the pendant in action. The firmware for the FluidDial has now been released. To use it, you will also need to update your main board's FluidNC firmware to at least 3.7.13 or later. Many thanks to the FluidNC dev team for their great development work. As always, treat any new update to FluidNC as “beta” until you've tested it.
This cradle is designed for holding the FluidNC Dial pendant on the YZ plate of a LowRider v3 CNC.
The remixed case bottom (included here) adds 7mm of depth, which helped me with the wiring install.
Placement on YZ plate:
There are two keys to good placement.
The first key is to avoid any chance of collision between the new cradle and your existing XZ lead screw stub. The two versions of the stub can be seen in the images below:



Assuming your LowRider is already assembled and functional, it's advisable to raise your gantry's Z height so that the stub is positioned so that you can see exactly how to place your new cradle to be far enough away from it.
Because I pre-drilled for, and installed, the first-generation prototype of the cradle, which had no side walls like the current generation, that older version could be positioned very close to the stub. When I later installed the current design with side walls, using the same pre-drilled holes, I had a collision issue, and had to carve out a small portion of my cradle. Because of that, I can only guess at exactly how far away (from the opening for the stub in the YZ plate) you need to install the cradle. My guess is between 1/8" and ¼" away should be enough. In the illustration below (from my 3D modeling in SketchUp), there are two vertical guidelines. One guideline is 1/8" from the opening, and the other guideline is ¼" from the opening. The cradle is installed with its edge somewhere between the two guidelines.

The second key to good placement is to make sure that you still have access to the two large holes in the YZ plate that allow access to the screws holding the gantry beam to the XZ plates.
In the illustration below (from my 3D modeling in SketchUp), you can see the two large holes highlighted in yellow. Notice that the cradle can be installed so that tool access to those holes is still allowable. Also, here again is another view of those two vertical guidelines. One guideline is 1/8" from the opening, and the other guideline is ¼" from the opening. The cradle is installed with its edge somewhere between the two guidelines.

FluidNC Pendant WIKI
http://wiki.fluidnc.com/hardware/official/M5Dial_Pendant
Please consider making a donation to support FluidNC and its ongoing, open-source development. See below for donation info and links:
Donations
FluidNC and Grbl_ESP32 are powered by donations. Donations are primarily used to pay for tools and hardware for firmware testing. Adding new features, like plasma torch height control, tool changers and VFD spindles is very expensive. The primary developers share this money. If you are asking for a custom feature or help with a controller from a manufacturer that is not sponsoring this project, please consider donating.
Via Github
A monthly donation via github is the preferred method. https://github.com/sponsors/bdring
Via Paypal
One time donations can be done via Paypal. https://www.paypal.com/donate/?hosted_button_id=8DYLB6ZYYDG7Y
Discord sponsor badges
If you donate, you will be added to the sponsor group. Your name will be highlighted in green and a sponsor badge will appear next to your name. Indicate your Discord username with the donation.
LowRider v3 CNC
For info on the free open-source plans and files for the LowRider, visit: https://v1e.com — and for discussion via the V1E forum, visit: https://v1e.com/forum
Change log:
- January 27, 2024 — initial v1.6 uploaded, which coincides with new releases of the other two editions (v1.4 and v1.5) which were modified to (like this edition) have less overhang during printing. See description for links.
Previous (parent of this remix) change log:
- January 27, 2024 —v1.4 uploaded, which was modified to have less overhang during printing. Coincides with new releases of the other two editions. See description for links.
- January 14, 2024 — v1.1 uploaded, which was modified to ensure the cradle can be installed without blocking the tool access holes that provide a way to reach the screws that mount the gantry beam to the XZ plates.
- January 11, 2024 — initial upload of v1.0
My PayPal tip jar: https://paypal.me/design8studio
Various LowRider 3 CNC remixes:
View all my models and remixes on Printables:
*Product links may be affiliate links, which add nothing to your price, but may benefit me by a small percent.