1 / 8
Guide clip to hold neatly two 4mm PTFE tubes together — zdjęcie 1
1 / 8

Guide clip to hold neatly two 4mm PTFE tubes together

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This will allow you to have a neat and decluttered PTFE tubing setup!

Ocena
0 / 5
Polubienia
17
Pobrania
246
Wydruki
0
Wyświetlenia
692
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Français en dessous :)

__________________________________________

With this quick and easy to print part you can neatly route two 4mm PTFE tubes together.

Very practical and easy to use. Gives a very nice look with our filament dryer and enclosure.

The part is available in various sizes following your liking. 
It depends if you want the two PTFE tubes close together or not too much.

6mm → Tubes are basically stuck together.
8mm
10mm
12mm

You can use them in conjonction to make the space go slowly bigger. We did that to accommodate our “Ikea Lack enclosure filament entry for 4 PTFE pneumatic connectors” better. We used a bunch of 6mm, then one 8mm, one 10mm, one 12mm to reach the entry.
     

You'll find a quick demo on our video (with plenty of info about filament drying and conservation) : 

Printing:

Material: anything you like should do!
Layer height: 0.2mm
Support: no
Orientation: place flat on the plate, print many at once ;)

Assembly:

You simply need to push in the PTFE tubing for a satisfying click.

The part is designed for 4mm PTFE and is only lightly holding onto the tubes. This avoids squishing the tube in any way.

__________________________________________

Grâce à cette pièce super rapide et simple à imprimer, vous pouvez router proprement deux tubes PTFE de 4mm ensembles.

Très pratique et facile à utiliser. Donne un super look à notre séchoir à filament et notre enclosure.

La pièce est disponible dans plusieurs tailles en fonction de vos préférence.
Cela dépend si vous préférez que les tubes PTFE soient très proches ou non.

6mm → Les tubes sont presque l'un contre l'autre.
8mm
10mm
12mm

Vous pouvez utiliser plusieurs tailles en conjonction pour agrandir progressivement l'espace. C'est ce que nous avons fait pour un beau résultat avec notre “Entrée de filament avec 4 connecteurs pneumatiques PTFE pour enclosure Ikea Lack”. Nous avons utilisé plusieurs 6mm, puis un 8mm, un 10mm, et un 12mm pour arriver a l'entrée de filament.


   

Vous pourrez le voir en démo dans notre vidéo ici (avec plein d'autres infos sur la conservation et le séchage du filament, en français): 

Impression:

Type de filament: Tout devrait bien fonctionner!
Hauteur de couche: 0.2mm
Support: non
Orientation: placer à plat sur la plaque, vous pouvez en imprimer plein d'un coup!

Assemblage:

Il faut simplement pousser le tube PTFE jusqu'à entendre un ‘clic’ satisfaisant.

La pièce est pensée pour des tubes PTFE de 4mm et n'est pas trop serrante, juste assez pour maintenir les tubes. Ceci pour éviter d'écraser les tubes!

Tagi