Bessey / Wolfcraft One-Hand Clamp to 20 mm Workbench Clamp conversion 2-Piece Version
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
0,98 € – 1,19 € netto (bez VAT)
Dla pliku: Benchdog Wolfcraft 2piece_0.4n_0.2mm_PETG_MINIIS_1h12m.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 1,09 € netto (środek widełek).
- Masa podana przez autora
- 12 g
- Czas druku podany przez autora
- 1,2 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Convert your Bessey EZM or Wolfcraft PRO M One-Hand Clamp into a workbech clamp for 20mm perforated grid plate.
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 78
- Wydruki
- 0
- Wyświetlenia
- 653
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial
This is the 2 Piece version of my One-Hand Clamp Mod which allows the use of Bessey EZM or Wolfcraft Pro M directly on your perforated grid plate Workbench. The “fixed” jaw slides on the clamps rail and allows the rail to be pushed into / below the Workbench.
This is only the 19.9 mm diameter version, which should fit most perforated grid plates.
The difference between Wolfcraft and Bessey is the position of the retaining hole and pin. The Bessey is 5mm longer which reduces the usable clamping distance by 5 mm.
The original can be found here: https://www.printables.com/model/773378-bessey-wolfcraft-one-hand-clamp-to-20-mm-workbench
A version without any screws can be found here: https://www.printables.com/model/774915-fast-and-screwless-bessey-and-wolfcraft-one-hand-c
Print settings:
8 Perimeters
50% Infill
Hardware:
1x Panhead screw M6x16 shortened to 14mm
1x Square Nut M6 (DIN 557)
You could try ¼'' equivalent, but i am uncertain it fits the hole in the Rail
Installation:
- Remove fixed jaw
- Push sliding Benchdog with flange towards movable clamp jaw onto Rail
- Push endstop onto Rail till holes align
- Secure with Nut and Screw
Usage:
The Workpiece (pressure point) has to be placed as far as possible away form the clamps rail due to how this type of clamp works mechanically. If the workpiece (pressure point) is to close to the Rail the Benchdog will simply slide out. To improve clamping, tilt the Clamps Rail away from the workpiece while tightening.
Uninstallation:
- Remove Nut and Screw
- Pump moveable jaw towards benchdog to push it off the rail
- Pull both benchdog pieces from Rail
(If still stuck, print the extraction tool or find something similar to extend the range of the movable jaw.) - Reinstall original fixed jaw
Notes:
The thickness of the workbench should not exceed 20mm
Commercial Benchdogs have an undercut below the flange to sit flush against the table. This would reduce the strenght of a printed part and therefor was not included. However, if the holes of your perforated grid plate are chamfered or rounded this is no problem.
.step-files are provided in case you need a different diameter or want to adapt to other clamps. If you do feel free to add a remix.