1 / 5
VORON 2.4 SKIRT CONNECTOR INSERT for CANBUS, fans, ERCF, PG7, XT30 2+2 & filament sensor — zdjęcie 1
1 / 5

VORON 2.4 SKIRT CONNECTOR INSERT for CANBUS, fans, ERCF, PG7, XT30 2+2 & filament sensor

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Fit a cable connector to any full open Hex on your VORON!

Ocena
5 / 5
Polubienia
177
Pobrania
691
Wydruki
8
Wyświetlenia
4796
Oceny
4

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

…Please be sure to hit like & post a make, I'd love to see your prints!

 

Print standard VORON settings, no supports required!

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

EDIT: I've updated the files to include my UNTESTED XT30 2+2 insert as well. At the moment it is untested as I'm still waiting for my connectors to be delivered. If you print it & it doesn't fit well let me know & I can adjust it. Please don't leave a bad review for that.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Add a cable connector to any full open hex with appropriate space on your VORON!

Modular design, no fittings, no lock rings, no screws! Press lock in place!

Use for fans, filament sensors, lights, CANBUS, ERCF, or anything you like!

Available connectors:

Blanking

PG7

MOLEX MICRO FIT 3.0 Single Row x2, x3, x4

MOLEX MICRO FIT 3.0 Single Row x2 + XT30

XT30 2+2 (UNTESTED)

Designed to be used with my remixed centre section models found here:

https://www.printables.com/model/790858-voron-24-300-350-rear-skirt-centre-section-open-us

 

Power fittings are on the lower row & MOLEX MICRO FIT 3.0 Single Row are on the upper hex's.

Be sure to align the curved edge on each insert to the curved shape of the skirts, the upper curve is very subtle but it is there & when aligned the inserts fit perfectly.

 

NOTE: TOLERANCES ARE EXTREMY TIGHT!!

Make sure your printer is set up well & is dimensionally accurate, tolerances are between 0.10-0.15mm! The connectors & the inserts are designed to be a tight locking fit.

They do fit if your printer is tuned well, if they don't fit I'd suggest looking into your setup & slicer profile & checking you have the correct accuracy.

Last photo of the XT30 I used for this, I know some may differ.

I found it good to use a tool or desktop to help push the connectors fully into place. Push connectors in from the rear then add crimped cables to the connector housings.

 

READ THIS:

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

DONT leave a bad review because you got different connectors to me & they don't fit well, or you got a bad print & you can't get the connectors in past elephants foot or over extrusion! That's NOT cool!

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••