1 / 4
608 Bearing Weight Mod for Xbox One and Series X|S Controller Stand — zdjęcie 1
1 / 4

608 Bearing Weight Mod for Xbox One and Series X|S Controller Stand

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Xbox One (and Xbox Series X|S) controller stand by io_roboto, modified for a 608 bearing-sized weight.

Ocena
0 / 5
Polubienia
2
Pobrania
19
Wydruki
0
Wyświetlenia
663
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Video Games
Licencja
Creative Commons — Attribution — Share Alike

NOTE: Model does not spin! It just has a hole inside to hold a 608 bearing-sized object for weight.

Effectively the same snug-fit Xbox controller stand as is io_roboto's, but instead with a 608-bearing sized hole inside for a weighted build (you can see this by with the 3D Viewer, with Wireframe or X-ray). I used those metal fidget spinner weights that are the exact size of a 608 bearing, alongside a plastic cylinder insert to make bridging smooth. If you have some other form of weight that fits inside a 7mm high cylinder with a diameter of 22mm, be my guest instead.

Tinkercad link here, in case you want to modify.

Printing Instructions
EDIT (2024-03-26): I have added a new version of this model with an Open bottom, on request of a friend. So, you don't have to deal with these complex instructions. For that model, you just need basic supports in the underside, and you can just directly insert a bearing/weight after removing supports.

Since you're looking for a weighted version of the original model by io_roboto, I would recommend at least a 15% infill or preferably higher, to add even more weight. I wouldn't go higher than 30%, personally.

Using the slicer of your choice, create some kind of print pause right before the roof of the hole is formed. I like using Prusaslicer's built in Color Change (the plus-shaped icon to the right) to pause the print. You do not have to change color, obviously, but this is just useful to pause the print easily to allow for inserting a weight mid-print.

It should look something like these images, to make sure the print pause is correct:

There should be a big hole right before the pause…

… And right above it, should be a solid roof.

(OPTIONAL) If you want to, I also recommend actually doing a color change earlier: right before the logo is printed. This is in case want to make a colored logo like in my print. However, this will unfortunately leave a small colored spot near the bottom of the indents where the controller sits, but this will be covered with a controller inside.

NOTE: If you are using fidget spinner weights instead of a 608 bearing, like I did, I strongly recommend you print the support cylinder STL either beforehand or with the print. This cylinder insert, when placed inside of the weights, will help your printer bridge over the weights. Else, a normal bearing should be support enough with its uniform-ish shape, even without covers. 

When you're actually printing, wait until the color shift happens to insert the weight of your choice. It is not very fun trying to fit the weight in while it's moving. If you chose to print a support cylinder, insert that in too, inside of the weight. I recommend you scale the thickness and size in case it doesn't fit normally.

The inserted weight should go in somewhat smoothly; I made the hole slightly oversized on purpose. If it's too big, take the weight out carefully and then apply glue into the hole. If it's too small, I recommend you modify my model in Tinkercad here into its parts, to make the hole bigger, and scrap this print attempt… or continue with a hole inside for a less-weighted print.

After the weights are inserted, and after confirming your filament is loaded and ready, continue the print. I recommend you watch the print to make sure your nozzle is riding safely over the weight insert, then leave to do other things. It should look like this during/after this step:

My fidget spinner weight insert, with the optional cylinder support (a bearing instead won't need it at all)…

… And the other side, nicely covered and bridged with no issue. Note the white spot due to the color change earlier for logo.

After that is done, and the print finishes, remove and enjoy. I also recommend to glue a felt bottom to the stand if you want further support, but that's entirely optional. I just had a lot of leftover felt from arts and crafts projects long ago.

 

I printed this using Jessie Premium PLA in Black and White, although I do not recall my infill… but it was pretty dense as you can see in my images. Again, I also used generic fidget spinner weights the size of 608 bearings, and glued some (black) felt at the bottom for grip.

Tagi