Filler Spool Holder Brace for Prusa Bear compatible with Prusa Filament Guide
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Prusa Bear brace for Filler spool holder that positions the spool in the same position as the stock Prusa spool holder
- Ocena
- 5 / 5
- Polubienia
- 33
- Pobrania
- 178
- Wydruki
- 3
- Wyświetlenia
- 1137
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is an adjusted version of the Prusa brace for the Filler Spool Holder for the Prusa Bear Frame that positions the spool in the exact same location as the stock Prusa spool holder relative to the front edge of the frame / top extrusion.
Looking for a brace for the original frame instead? Check out the Filler Brace for the Original Frame.

![]() | ![]() | ![]() |
Filament Guide
The brace has an attachment interface for the Prusa Filament Guide at the same position as the stock spool holder so that the guide hole is in the same position relative to the spool as with a stock setup.
However, since the Filler spool holder positions the spool further away from the center of the brace than the stock spool holder, a one-sided and lengthened filament guide is needed in order to position the guide hole in the center of the spool.
» Download Modified Filament Guide

Required Hardware
| Qty | Description | Sourcing |
|---|---|---|
| 4-6 | M5x10mm Low Profile Screw or Button Head or Socket Head Cap Screws | OpenBuilds, Aliexpress (BHCS), 3DWare |
| 4-6 | M5 Drop-in T-Nut | OpenBuilds, Aliexpress, 3DWare |
Printing
Print the part in the original orientation. The STLs are pre-rotated for printing. I'd recommend printing this part extra beefy with a high perimeter count and high infill percentage.
Print Settings
- Material: PETG, ASA, ABS, etc.
- Extrusion width: 0.4mm - 0.45mm
- Layer height: 0.2mm
- Perimeters: 6
- Infill: 30% Gyroid
- Supports: Yes, support enforcer
Supports
Place a support enforcer at the top to support the opening for the spool holder. Only the opening needs to be supported. The interior is supported by a bridging. You printer must be capable of bridging about 20mm. If you get sag on the bridging layer you might have to use a file.

Assembly & Installation
Note: The following illustrations show only two screws in the back of the brace. You should use at least two but you can also use 3 or 4.
Step 1
Drop 2 T-Nuts into the top extrusion and space them 20mm apart.

Step 2
Insert 2 or 4 M5 screws into the back of the brace and loosely screw on the T-Nuts.
Do not insert the top screws yet.

Step 3
Place the brace on the extrusion.

Step 4
Slide the brace over the two T-Nuts that you dropped into the top extrusion in step 1 and make sure the holes are precisely above the T-Nuts.

Step 5
Insert the remaining two M5 screws and loosely thread them into the T-Nuts in the top extrusion. Slide the whole assembly to your preferred position. Then tighten all screws to the final torque.

Step 6 (optional)
Clip the filament guide onto the mounting interface on brace and secure it with the M3 screw and hex nut. Check out the Filament Guide page for specific instructions.



