LayersFactory
Zgłoś model
1 / 18
Flashforge Adventurer 5M (AD5M) Nozzles Box and Accessories Box - two styles to choose from, including sets that attach to back of printer v1.2 — zdjęcie 1
1 / 18

Flashforge Adventurer 5M (AD5M) Nozzles Box and Accessories Box - two styles to choose from, including sets that attach to back of printer v1.2

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Doug Joseph (design8studio)

Doug Joseph (design8studio)

@design8studio

Adventurer 3, 4, 5 (AD5M) Nozzle Box & Accessories Box, 2 style choices, incl. sets that attach to back of printer v1.2

Ocena
4,95 / 5
Polubienia
387
Pobrania
3128
Wydruki
21
Wyświetlenia
16 942
Oceny
20

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution
SzczegółyPliki (32)Wydruki i komentarze (Wydruki: 21) (Komentarze: 59)Remiksy (2)Kolekcje (505)Powiązane

VIDEOS

These two short videos explain everything:

NEW

New as of January 28, 2026 —  The following additions and improvements were made:

  • Now the boxes can be mounted on the sides of the printer. Click here: 

     

New as of January 27, 2026 —  The following additions and improvements were made:

  • Ver 1.2 - Some comments mentioned difficulty in getting the filament inserted as the hinge pin. I think some filament is a teensy bit thicker than others. I am adding version 1.2 which has slightly larger holes in the hinge parts, to grant a little more tolerance. I will leave the v1.1 files just in case.

New as of April 1, 2024 —  The following additions and improvements were made:

  • Added a new, larger box for storage of all the factory accessories that ship with AD5M. 

  • Tweaked the back “mount” portion of the smaller box (the one for nozzles) (as well as the new box), so it can work with stock flat-head screws that were provided by factory to mount the spool holder. Previously it worked with cap-head screws.

  • Added a new second mount that can allow two boxes to be hung on back of one printer, one using the screw holes originally intended for the spool holder, and another mount for a second set of unused screw holes lower down on the printer. 

 

Cool storage for four nozzles for Flashforge Adventurer 5 (AD5M).

Uses 1.75mm filament as the hinge pin.

Two options to choose from:

  • Box and lid

  • Box and lid that mount onto back of AD5M printer, whenever the DIY printed enclosure is in use.  NEW as of April 1: added an alternate mount that uses two other spare holes on the back of the printer!

Print settings

Print as oriented. Prints without need of supports. I used 10% infill on the lid, and 15% infill on the base and the mount. I used 2 perimeter walls, with a 0.4 mm nozzle.

IMPORTANT NOTE ABOUT LAYER HEIGHT

I printed with 0.2 mm layer height. If a thicker layer height is attempted, such as 0.28mm, it will make the hinge holes too small for the hinge pin (the 1.75mm PLA piece) to be inserted. My advice is to stick with no thicker that 0.2mm on layer height. 

 

Installation for mounting to back of AD5M

The DIY printed enclosure mounts the spool holder in a different spot, which frees up the two screw holes that formerly attached it. The mount in this design is intended to attach by using those same screw holes.  NEW as of April 1: added an alternate mount that uses two other spare holes on the back of the printer! Attach the mount with two screws, M3 x 8mm or M3 x 10mm, and then slide the box base onto the mount. That's it. You're done.

 

Change Log

  • January 27, 2026 — Ver 1.2 - some comments mentioned difficulty in getting the filament inserted as the hinge pin. I think some filament is a teensy bit thicker than others. I am adding v1.2 which has slightly larger holes in the hinge parts, to grant a little more tolerance. I will leave the v1.1 files just in case.

  • March 30, 2025 — Had to replace the “PLATED SET (larger for accessories)” file because it contained a wrong file. Somehow I had accidentally uploaded a base for the box that was 2.1mm too short. The stand alone file was correct. This is now fixed. Kudos and thanks to @zcapers_3104688 who found and pointed out the error. 

  • April 1, 2024 —  The following additions and improvements were made:

    •  Added larger box for storage of all factory accessories for AD5M. 

    • Tweaked the back “mount” portion of the smaller box (the one for nozzles) (as well as the new box), so it can work with stock flat-head screws that were provided by factory to mount the spool holder. Previously it worked with cap-head screws.

    • Added a new mount that can allow two boxes to be hung on back of one printer, one using the screw holes originally intended for the spool holder, and another mount for a second set of unused screw holes lower down on the printer.   

  • March 21, 2024 — Upload of original remix, with only the nozzle box options.

 

Other cool options for the AD5M

 

You may also like my other AD5M related design work:

Use Klipper stuff on AD5M stock hardware,

Check out other cool AD5M related options here:

 

My PayPal tip jar: https://paypal.me/design8studio