1 / 3
FPV mounting kit for DJI O3 on Losi Lasernut U4 RC model car — zdjęcie 1
1 / 3

FPV mounting kit for DJI O3 on Losi Lasernut U4 RC model car

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Turn your RC rock racer into a real FPV banger!

Ocena
0 / 5
Polubienia
15
Pobrania
73
Wydruki
0
Wyświetlenia
1677
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Losi Lasernut U4 – #FPV banger!

 

great FPV perspective:

 

good camera protection:

 

flexible & robust antenna mount:

 

The idea

I wanted the FPV camera as high as possible on the car for better view. I also wanted the whole build to look as scale as possible. So I came up with the idea of disguising the camera as additional headlights on the car's roof, hiding the pan servo under the pilots and the air unit casing look like some over–sized air conditioner. 


Camera mount and pan servo are connected with a black 3 mm GFK rod, from outside you do not see much of it. The air unit "AC" holds also a fan to keep it cool. You need tweezers and to remove the rear section of the original body to get to the SD card, but this is only done once per session and in my opinion the better look is worth this little effort. The custom body mount bolts combined with standard clips makes that body section easily accessible.

 

Printing

Most parts are designed to be printed in ABS–like resin. I'd like to give you pre–supported files, but still being a resin noob, my results are … mixed. So, try your best, good luck! 
 

  • c08-servo_plate and e03-rear_stabilizer_plate were printed in PETG

  • e01-antenna_rod_base-TPU should be printed in TPU, obviously; 0.4 mm nozzle, 0.2 mm layer height, 2 perimeters, aligned seams, 30 % cubic infill, no supports

And yes, I know my model files are huge. I export them with high detail settings so they look really nice when printed using appropriate resolution. 😁

 

Inner Threads

There are no inner threads modeled. In my experience it's best in resin to tap the threads. So you need a M3 and a M2.5 tap. The M4 bolt just finds it's way into the TPU rod, no thread needed there.

 

Additional parts needed

  • DJI O3 air unit

  • 200 mm camera cable

  • Arduino ARM

  • Noctua NF-A4x10 5V (or similar)

  • heat sinks for the air unit (optional)

  • 3 mm GFK rod (camera mount, antenna)

  • 15T mini/micro servo for pan

  • M2×12 bolt + hex nut (servo connector)

  • some M3 and M2.5 bolts

  • one M4×25 bolt (antenna base)

  • two standard body clips

  • one paper clip (glued into body bolts)

  • some heat shrink tube

  • some glue

  • vinyl wrap for the roof (optional)

 

Assembly

Cut away the fake radiators behind the pilots.

 

Tap threads and insert fan in a01 air unit mount w/ M3 bolts.

 

Glue on the grill.

 

Place the mount centered and fix it w/ right and left inner bars (a02, a03) using M3 bolts.

 

Glue e03 under the lexan interior to stabilize the rear section.

 

Mount e01 antenna rod base w/ M4 bolt and the air unit using a05 air unit holder plus four M2.5 bolts. (Some of the title photos above show a temporary antenna mount, the real one is only 1 part.)

 

Drill a hole in the console between the pilots, mount c08 servo plate and the pan servo (leaning forward).

 

Screw c07 connector to the servo, glue 3 mm GFK rod into c06 connector and put both connectors together with M2 bolt and hex nut. Here you can later separate the rod from the servo in case of replacement.

 

Drill a hole into the roof, insert c04 tube for camera mount and glue on c05 washer.

 

Also cut the rear border of the roof; the air unit casing is a snug fit. 😉

 

Put the roof back on the car's cage, glue c03 camera mount to the GFK rod. Caveat: a) center the pan servo before doing this b) check that the mount is facing in the right direction, camera won's fit otherwise. Mount the camera with it's own bolts.

See also, how additional headlights and c01 camera protector (using c02 hex nut w/ tapped M3 inner tread underneath the roof) are mounted.

 

Mount the antenna w/ heat shrink tube on a 3 mm GFK rod, insert this into e01 antenna rod base (some silicone grease may help) and fix the main cover w/ four M2.5 bolts.

You can access the SD card w/ tweezers later on.

 

For better accessibility of the SD card replace the stock bolts w/ the printed bolts (glue paper clip wire into those before (& cut to length) and tap M4 threads into cage). You can then mount the body part (drill larger holes) using simple body clips (black ones look really nice).

 

Did I forget something? Please let me know and help improving these instructions. Thanks.

 

More 3D printed parts for the Lasernut

Update 2026/02/14

Added FreeCAD files upon request. Please note that these files were made using FreeCAD 0.2x and may need some work-over for FreeCAD 1.0 or newer. 

Support my work

I really enjoy designing parts for the hobby. If you want to support my work, please give my videos a like and subscribe to my YouTube channel. And if you have a few bucks spare, consider helping me pay my coffee bill. Thanks. ☕ 

 (→ PayPal)