1 / 5
HeroMe 7 Gantry Adapter For Wham Bam Mutant v2 on the CR-30 — zdjęcie 1
1 / 5

HeroMe 7 Gantry Adapter For Wham Bam Mutant v2 on the CR-30

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A Gantry Adapter designed to attach to the Mutant v2 on a CR-30 Infinite Z Belt Printer

Ocena
0 / 5
Polubienia
1
Pobrania
20
Wydruki
0
Wyświetlenia
395
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

The stand-offs on my linear rails Gantry Plate for my CR-30 3DPrintMill broke, causing me to get a lot of back-and-forth shifting on my prints. I was unable to find a replacement gantry plate, so I decided to reach out to Wham Bam Systems regarding their Mutant v2 Universal Tool Swapping System. They worked with me and designed a new Gantry Plate for the CR30 to allow me to attach the Mutant to my CR-30. 

Once I got the Mutant installed, I found the nozzle was nowhere near being able to touch the belt, for various reasons. I made adjustments to my CR-30 to lower the X-Axis as close to the bed as I dared (I have maybe 2mm of hardware clearance). I then used TinkerCad to mod the original Mutant Gantry Mount to design one specific to the CR-30. 

This model drops the primary mount about 30mm below the Mutant's Mobile Plate, allowing the nozzle to properly contact the belt and letting me resume printing. I also added a brace to help brace it against the Mutant to help prevent it from bending. Not sure this is required, but it doesn't appear to be hurting anything.

Some Notes:

  • I am using the Stock Hotend
  • Notes about installing the Mutant
    • I had to cut the wires closer to the hot end. This meant I had to use a new Heat Cartridge and a new thermistor since the wires were now too short to reuse.
    • The spacer for my Y-Axis Linear Rails no longer fit (I will have to remodel it later to line the belts back up.
    • The ground doesn't have a connection location. I have the wire hanging right now (not connected to the mutant).
    • The X End Stop Switch connects to the Gantry Plate, not to the Mutant.
    • For a stock system, you need only wire/cut:
      • The Heat Cartridge
      • The Thermistor
      • The Heat Break Fan
      • The Part Cooler Fan
  • The models I used for my HeroMe 7 Were:
    • This Gantry Adapter
    • HMG7.2 Universal Base V2
    • HMG6-dual-5015-6deg-brace-inserts
    • HMG7.3 Creality OEM-CR10S-Ender3-5 2-Screw Mount V2
    • HMG7 Creality OEM-CR10S-Ender3-5 Skirt V2
    • HMG7.4 Cable Tower Tube Tall Right
  • You will likely need to adjust your Min/Max on your X and Y axes as otherwise, you will either run into the Bed Leveling Knobs or you will run into the motors or frame.
  • You will lose some print space. I went from 215x250 to 183x233.
    • I believe we can get the X-Axis back, but only if A) You sacrifice height and B) we can get a replacement for the bed leveling knobs that the ducts don't run into. 
  • I printed the gantry using the same suggested settings as the HeroMe 7 except for supports.
    • Oriented with the front on the bed (brace up)
    • 3 Walls
    • 30% Infill
    • ABS
    • Supports
  • When aligning the part cooler to the nozzle, I held the hotend assembly at the normal vertical angle (90*) and then used the HeroMe Spacer to align the ducts correctly and tighten everything down.

Tagi