1 / 3
Ultra-Low-Friction Filament Guide for Elegoo Neptune3 Pro (and others with the same frame top shape) — zdjęcie 1
1 / 3

Ultra-Low-Friction Filament Guide for Elegoo Neptune3 Pro (and others with the same frame top shape)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Designed to minimise strain on the extruder when printing with "squeaky" filaments like GiantArm Clear PLA

Ocena
0 / 5
Polubienia
6
Pobrania
32
Wydruki
0
Wyświetlenia
509
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

TL;DR - Go straight to the printing and building sections!

I normally print with Elegoo's excellent PLA+ filament as I've found it to be highly reliable and prints beautifully cleanly. But then I wanted to use a clear PLA filament, and the reviews I read suggested that GiantArm's Clear PLA was the clearest of all so I bought some.

But… it's quite tricky stuff, it's quite brittle and the filament can snap if you bend it too much. It does print VERY nicely though! However the worst thing is that the surface is so shiny and “squeaky clean” that it sticks to itself slightly on the roll (which isn't wound perfectly despite the marketing pictures) and my direct extruder literally screams trying to pull it off the roll and through the runout sensor. 

I worried that at some stage it might start slipping in the extruder, or even damage it, so the first thing I did was pull out some filament from the roll and leave it dangling in a loop so that the extruder only had to take it from thin air, and that worked fine until the extruder used up the loop and then SQUEEEEEEAAL again!

So I designed a spool adapter because the GiantArm spool is 75mm ID which is pretty silly IMO as the amount of force required to pull filament off a roll with a large ID is substantially higher than that required to pull it off a roll with a small ID, something I vaguely remember from school maths as being a “moment arm” where the distance from the axis of rotation determines the force required to turn it. Think spanner - a long handled spanner will deliver far more force to the nut for the same effort than a short-handled spanner :o)  This did reduce the screaming <g>, but didn't eliminate it.

So I designed this Ultra Low Friction arrangement with a neat clip that attaches it to the printer frame when needed and then can be easily unclipped when it's not needed.

The 608 bearings actually came from our old Dyson DC07 motor when it went bang and I had to buy a new motor, shame to waste good bearings, but they're very cheap to buy and very commonly used in printing projects, you can pick up several for a few quid. 

PRINTING:

I used the default settings for everything (0.2mm layers, 0.4mm nozzle, 3 walls, 6 tops/bottoms, grid infill 15%) except as specified below:

BASE MOUNT - To get a cleanly printed hole for the bearing axle, I used “support to buildplate only” zigzag 25% support density. The attached 3MF is for Elegoo Neptune3 Pro and includes this setting for folks with that specific printer.

ROLLER HOLDER - This is a tricky one, I feel it needs to be printed as orientated in the supplied STL, and needs heavy support, I think I used about 25% gyroid support to buildplate but play with it in your slicer until you're happy you have enough to get a clean edge on the filament un/loading slot - I don't tend to use this slot because getting the filament past the V-Ring edge is quite tight and I just poke the cut filament through before loading it into the extruder, but the option to attach/detach the filament guide without removing the filament from the extruder is there if you want to use it.  

Parts Needed:

1x Base Mount

1x Roller Holder

1x Filament Bearing V-Ring

2x Filament Roller Spacer

1x Back Bearing Sleeve

1x Back Bearing Washer

1x M3x25 bolt

1x M3x16 bolt

2x M3 nut

1x M3 washer

2x 608 bearing

BUILDING:

See annotated photo of parts. 

ROLLER SECTION:

Bearing goes in V-ring, add spacers (axle), slot it into the Roller Holder and secure with M3 nut/bolt/washer, use threadlock if you like or even a locknut, I didn't bother, it shouldn't come undone.

MOUNT SECTION:

M3 nut goes in fat end of Back Bearing Sleeve, poke through bearing, add Back Bearing Washer which will be TIGHT and might even need a wave with a deburrer, push protruding thinner end of Back Bearing Sleeve into hole in Base Mount and secure with M3 bolt. Not intended for a locknut - the extra height will probably foul on the Roller Holder, so if you want to secure it then a smear of threadlock is the answer, or just do it up nice and tight :o)

FINAL ASSEMBLY:

The two sections are designed to push-fit together snugly. Filament tension should ensure these parts don't separate in use, but ideally they should mate with good friction so they stay together when taken off the printer. I had to clean up the receiving hole in the Roller Holder a bit with a Dremel to get the precise amount of friction I wanted. It all depends on how well it printed on your machine, I deliberately left it a bit tight so you can adjust to suit like I did rather than risk it being loose. I included some poke-holes in the Roller Holder so you can carefully knock the bearing out if you made it too tight, and adjust more - but better to tweak and try a few times and get it right.

Note that Elegoo for some reason made the top bar asymmetric - thanks Elegoo it took me 3 goes to get that right, HAHAHAHAHA, so I've labelled the Base Mount with a “TOP” engraving, make sure you put that face on the top of the bar or it won't fit properly. 

Once complete, it should click satisfyingly in place and stay there until you want to remove it.

FINAL THOUGHTS:

Even this didn't completely eradicate all squeaks from this troublesome filament, but it did massively improve it to the point where I no longer feel the need to babysit and “help” the extruder by pulling loops in the filament! I will probably add an even smaller spool adapter to further improve the “moment arm” but if you want to do that, you'll have to print a secondary spool support arm and attach it to the right hand side of the printer like I did, the one I printed has a smaller lip on the end so it will accept smaller ID spools. I used this one https://www.printables.com/model/579907-elegoo-neptune-3-and-4-replacement-filament-spool which has been superb.

I made a spool adapter for 75mm (e.g. GiantArm) ID spools here https://www.printables.com/model/814940-spool-adapter-for-giantarm-clear-pla-or-any-75mm-s 

Best of luck :o)

If you enjoy this model please Like it and show us your print. 

If you REALLY like it, https://www.buymeacoffee.com/gigabeast :o)