Filamenthalter für Prusa MK-Drucker/ Filament holder for Prusa MK printers
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Flexibler Doppelfilamenthalter mit gedruckten Gleitlagern/ Flexible double filament holder with printed plain bearings
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 94
- Wydruki
- 0
- Wyświetlenia
- 618
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
For English see below.
14.06.2024: siehe auch/ see also "Upgrade für mein Modell Filamenthalter für Prusa MK-Drucker/ Upgrade for my model Filament holder for Prusa MK printer”. Erweiterung um eine Schnellspannmutter/ Extension with a quick-release nut
28.03.2025: Eine weitere Hülse und Konus mit Gewinde M36x3 und einer Nut auf der Innenseite der Lagerflächen. Hier kann die Naht, die beim Drucken entsteht, eingelegt werden. Dadurch ist praktisch keine Nacharbeit erforderlich. Nur als STL-Datei vorhanden./ Another sleeve and cone with an M36x3 thread and a groove on the inside of the bearing surfaces. The seam that is created during printing can be inserted here. This means that practically no reworking is required. Only available as an STL file.
-------------------------------------------------------------------
Diese Halterung für die Filamentspulen wird auf den Rahmen des MK-Druckers montiert. Bei meinem Drucker hat die obere Strebe die Maße 40,4mm x 6,2mm. Die Konstruktion enthält gedruckte Gleitlager, so dass die Filamentrolle leicht, aber nicht zu leicht, abrollt. Es sollten viele Filamentrollen mit unterschiedlichen Abmessungen funktionieren.
Vorgehensweise:
- Alle Teile ausdrucken und abkühlen lassen.
- Glätten der Lagerflächen bei "Achse#x.stl" und "Hülse#x.stl" mit 120er Schleifpapier bis beide Teile leichtgängig zusammenpassen ohne zu klappern. Hauptsächlich muss die beim drucken entstehende Naht abgeschliffen werden.
- Falls nötig alle Gewinde gängig machen. Zur Unterstützung kann man eine hauchdünne Schicht Wachs auftragen. Ich nutze dazu ein Teelicht, dass ich einmalig ganz leicht über die Fläche reibe. Nicht zu viel, sonst klebt es! Letztlich sollten alle Gewinde sehr leichtgängig sein.
- Die Lagerflächen von "Achse#x.stl" sehr dünn mit Wachs einreiben.
- Die Teile montieren.
'Verbinder.stl' muss liegend gedruckt werden, um eine gute Festigkeit zu erreichen.
Ich habe auch eine Filamentführung in Anlehnung an den "Filament Guide" von Prusa Research entwickelt. Diese Führung ist sehr nützlich, um ein Verheddern des Filaments bei vollen Spulen zu verhindern. Dazu benötigt man
- 2 Zylinderschrauben M3x12mm
- 2 Zylinderschraube M3x16mm
- 2 Unterlegscheibe U3
- 4 Stoppmuttern M3
- 2 Stück PTFE-Schlauch außen 10mm/ innen 8mm; 7,5mm lang
Translation: DeepL
This holder for the filament spools is mounted on the frame of the MK printer. On my printer, the upper strut measures 40.4mm x 6.2mm. The design includes printed slide bearings so that the filament spool rolls easily, but not too easily. Many filament rolls with different dimensions should work.
Procedure:
- Print all parts and allow to cool.
- Smooth the bearing surfaces of "Achse#x.stl" and "Hülse#x.stl" with 120 grit sandpaper until both parts fit together smoothly without rattling. The main task is to sand down the seam created during printing.
- If necessary, make all threads smooth. You can apply a very thin layer of wax to help. I use a tea light for this, which I rub very lightly over the surface once. Not too much, otherwise it will stick! Finally, all threads should run very smoothly.
- Rub the bearing surfaces of "Achse#x.stl" very thinly with wax.
- Fit the parts.
'Verbinder.stl' must be printed horizontally in order to achieve good strength.
I have also developed a filament guide based on the "Filament Guide" from Prusa Research. This guide is very useful to prevent the filament from tangling when the spool is full. For this you need
- 2 cylinderhead screws M3x12mm
- 2 cylinderhead screw M3x16mm
- 2 washer U3
- 4 stop nuts M3
- 2 pieces PTFE hose outer 10mm/ inner 8mm; 7.5mm long