Air Purifier - "Old Panda" model
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
DIY air purifier elements, with IKEA filters / Eléments pour purificateur d'air DIY, avec des filtres IKEA
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 35
- Wydruki
- 0
- Wyświetlenia
- 552
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Medical Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
28/05/2023: Upload of the old model, an improved version will be updated shortly.
28/05/2023 : Upload de l'ancien modèle, une version améliorée sera mise à jour très prochainement.
-----------------
English :
Element for making a DIY air purifier.
Suitable for air purification against aerosols produced by breathing, against wood dust, against fine particles up to 10 microns.
Designed primarily to combat epidemics of Covid-19, it is recommended to use filters in combination with masks and vaccination.
Panda
- ~102€, 538m3/h, 42db at 1m, 45.4x36.4x36.4cm, ~3kg
- For 4 air changes per hour (ACH) (if public masked) : Covers 50m².
- For 6 air changes per hour (if public not masked): 33m².
- Usage: Placed on the ground, on a table or piece of furniture ; Dismountable
- Time: 60mn of assembly and 8h of 3D printing
Parts to be purchased :
- 8x Arctic P14 Fans (6€50 if bought by pack of 5; otherwise 11€ each) : Arctic site
- 4x HEPA filter STARKVIND IKEA (10€) : IKEA site
- 1x 3pin x8 splitter (1,50€) : Aliexpress
- 1x Power supply 12V 1.5A AC-Molex (3€) Aliexpress
- 1x On-Off button Molex-AC (2€) : Aliexpress
- 60 screws M5 ~8mm
- Optional: 1x battery 12v 31Ah DC-DC (from 9€ to 15€) : Aliexpress
Parts made by 3D printer:
- 8h printed with a Flsun V400; 370g / 110m of filament for the set
- Print 4x PandaA ; 4x PandaB ; 4x Square ; 16x Rectangle ; 4x Foot20cm
Assembly:
- General note, screw all fans with their white logo facing inwards
- General note, orient the fan so that the power cable exits towards one side of the block, this side will be the bottom of the air purifier.
- Place 4 fans with the white logo facing inwards, forming a square. Using 4 screws and a Square element, fasten the 4 fans in the middle. Repeat the operation on the back of these 4 fans with 4 other screws and another Square element.
- On the side where the white logos are visible, use 8 screws and 4 Rectangle elements to screw in between 2 fans.
- On the side where the white logos are NOT visible, screw with 2 screws, 1 Rectangle and 2 PandaA pieces on the 2 fans on the bottom side of the purifier, repeat with 2 screws, 1 Rectangle and 2 PandaB pieces. Screw in all remaining positions with 8 screws and 2 Rectangles. Always screw in this direction: screw => rectangle => PandaA or B => fan.
- Repeat the last 3 operations with the other 4 fans, 22 screws, 2 Square elements, 8 Rectangle elements, 2 PandaA parts and 2 PandaB parts.
- On one of the fan blocks, place the filters with the black foam towards the inside of the purifier and run the cables out of the box under one filter. Then place the other fan block so as to hold the whole assembly together.
- Insert the 4 Feet into their slots and turn a quarter turn (you can repeat the operation to remove them).
- Connect the 3-pin plugs to the 3-pin splitter, the knob to the splitter, and the knob to the power supply or a battery.
Maintenance:
- 6 months if used in standard condition H24/7-7 for a filter, replacement for 10€ each filter
- 10 years for fans
--------------------------------------------------
Français :
Element pour la fabrication d'un purificateur d'air DIY.
Convient pour l'assainissement de l'air contre les aérosols produits par la respiration, contre les poussières de bois, contre les particules fines jusqu'à 10 microns.
Conçu principalement pour lutter contre les épidémies de Covid-19, il est recommandé d'utiliser des filtres en combinaison des masques et à la vaccination.
Panda :
- ~102€, 538m3/h théorique d'air filtré par heure (CADR), 42db à 1m, 45,4x36,4x36,4cm, ~3kg
- Pour 4 changements d'air par heure (ACH) (si public masqué) : Couvre 50m²
- Pour 6 changements d'air par heure (si public non masqué) : 33m²
- Usage : Posé au sol, sur une table ou meuble ; Démontable
- Temps : 60mn d'assemblage et 8h d'impression 3D
Pièces à acheter :
- 8x Ventilateurs Arctic P14 (6€50 si acheté par pack de 5 ; sinon à l'unité 11€) : site d'Arctic
- 4x filtre IKEA STARKVIND (10€) : site IKEA
- Répartiteur 3pin x8 (1,50€) : Aliexpress
- 1x Alimentation 12V 1.5A AC-Molex (3€) : Aliexpress
- 1x Bouton On-Off Molex-AC (2€) : Aliexpress
- 60 vis M5 ~8mm
- Optionnel : 1x batterie 12v 31Ah DC-DC (de 9€ à 15€) : Aliexpress
Pièces fabriquées par imprimante 3D :
- 8h imprimé avec une Flsun V400 ; 370g / 110m de filament pour l'ensemble
- Imprimer 4x le fichier PandaA ; 4x PandaB ; 4x Square ; 16x Rectangle ; 4x Foot20cm
Montage :
- Note générale, visser tous les ventilateurs avec leur logo blanc vers l'intérieur
- Note générale, orientez le ventilateur de façon à ce que le câble d'alimentation sorte vers un coté du bloc, ce coté sera le bas du purificateur d'air
- Placez 4 ventilateurs face logo blanc visible et formez un carré. Visser avec 4 vis et un élément Square la partie centrale composée des 4 ventilateurs. Répétez l'opération au dos de ces 4 ventilateurs avec 4 autres vis et un autre élément Square
- Sur le coté où les logos blancs sont visibles, visser avec 8 vis et 4 éléments Rectangle, entre 2 ventilateurs
- Sur le coté où les logos blancs NE SONT PAS visibles, visser avec 2 vis, 1 Rectangle et 2 pièces PandaA sur les 2 ventilateurs du coté bas du purificateur, répétez l'opération avec 2 vis, 1 Rectangle et 2 pièces PandaB. Visser à tous les emplacements restant avec 8 vis et 2 Rectangles. Visser toujours dans ce sens : vis => rectangle => PandaA ou B => ventilateur.
- Répétez les 3 dernières l'opération avec les 4 autres ventilateurs, 22 vis, 2 éléments Square, 8 éléments Rectangle, 2 pièces PandaA et 2 pièces PandaB
- Sur l'un des blocs de ventilateur, placer les filtres avec la mousse noire vers l'intérieur du purificateur et faites passer les câbles hors de la boîte sous l'un filtre. Puis placer l'autre bloc de ventilateur de façon à tenir l'ensemble
- Insérer les 4 Pieds dans leurs emplacement puis effectuer un quart de tour (vous pouvez répéter l'opération pour les démonter)
- Brancher les prises 3pin au répartiteur 3pin, le bouton au répartiteur, le bouton à l'alimentation ou à une batterie
Entretien :
- 6 mois si utilisé en condition standard H24/7-7 pour un filtre, remplacement pour 10€
- 10 ans pour les ventilateurs
