Arcade Joystick - KCL V7.1
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A Korean style arcade lever. For those who don't want to permanently mod their Japanese style arcade stick housing.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 59
- Wydruki
- 0
- Wyświetlenia
- 273
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Video Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I started designing this arcade lever since there was nothing that really fit my needs 100%. Access to a good detacheable shaft system was a necessity along with a Korean lever feel. Originally based as a Sanwa JLF/Samducksa 309 hybrid the KCL was born.
A hopefully useful PDF guide is also attached. Any feedback is appreciated!
Features:
Supports both Crown and Fanta grommets (For the Fanta I only have the 25 grommet here, not exactly sure how the grommets past that perform)
Can use a standard JLF shaft or the Phreakmods JLF shaft
Pretty much as short as a JLF
Changeable Collar gates that match the shaft
Almost all of the parts can be changed without removing the entire lever. For the Collar/Plate/Base the lever would have to be fully removed from the case.
Hex nuts be gone!
Print Notes:
0.1-0.2mm Layer Heights, I did all mine in 0.2mm.
I've only printed this in PETG so it is the filament I recommend. No abrasive filaments for the components which touch the shaft.
Scarf seams are a must for the Bobbin and Actuator to help keep the shaft in the centre. Recommended for the Squircle and Circle gates.
Supports are required for the Bobbin. Alternate support interface material is highly recommended for the Bobbin as well. Both are recommended for the base, but you can skip the alternate support interface material if you want.
The .f3d file is provided for the Collar/Bobbin/Actuator so you can get those parts to fit nicer with your stick housing and shaft. Ideally the Collar should fit snug in the hole of your housing provided the collar goes through and should not stick out of the housing. The Bobbin and Actuactor should have little to no wobble on your shaft.
Assembly Materials:
8 x M3 Heat Set Inserts (5-5.7mm tall)
4 x M4 Heat Set Inserts (6mm tall)
8 x M3x16 Socket Cap Screws
4 x M3x12 Socket Cap Screws
4 x M4x10 Counter Sunk Screws
1 x 17id-30mmOD 1mm thick washer (A 1mm washer for an AXK1730 bearing is perfect)
SuperGlue
Note: There is some flexibility with the screw sizes, please refer to the instructions.
Arcade Parts:
1 x JLF Phreakmods EX Groove/JLF Shaft
1 x JLF E-Clip
1 x Seimitsu MS-P50/SE/SS Mounting Plate
1 x Samducksa/Crown grommet for the 300 series OR Fanta grommet
1 x Dust Washer
1 x Whatever top you want
Assembly Tools:
Soldering Iron (Preferably with heat set insert tips)
A piece of flat metal
Screwdriver
Optional:
Samducksa 5 pin interface for 303/309
JLF Spring
Lubricant
Changelog:
17/03/2026 - V7.1 Released
25/03/2026 - Fixed KCL Parametric.f3d, an extrusion shouldn't error out when editing the Collar Width parameter.