1 / 4
TENS 7000 AC Wall Power Adapter (No More Wasted Batteries!) — zdjęcie 1
1 / 4

TENS 7000 AC Wall Power Adapter (No More Wasted Batteries!)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

TENS 7000 Therapy Device 9V Wall Power Adapter (Never change another battery!)

Ocena
0 / 5
Polubienia
3
Pobrania
39
Wydruki
1
Wyświetlenia
446
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

As someone who has been grappling with chronic SI joint issues that constantly pinch my sciatic nerve, causing debilitating pain, I've found that traditional medical interventions have been largely ineffective. The only treatment doctors can offer are deep steroid injections, which cost $350 each and provide a mere 20-40% relief for about a month. To make matters worse, these injections can only be administered every three months, and their efficacy is not guaranteed, as the doctor may miss the joint during the injection process.

Having exhausted various treatment options, including potent painkillers, I've discovered that TENS therapy has been the most effective in managing my pain. TENS therapy involves placing two electrode pads over the affected muscle or nerve, and the electrical voltage causes involuntary contractions that massage the muscle or numb the nerve entirely with sufficient power. I've experimented with five different TENS devices, and I've found that those with internal rechargeable batteries were inadequate and did not generate enough power for deep nerve therapy, only managing to elicit muscle twitches. The TENS 7000 is the only unit I've encountered that can reach a power level capable of completely numbing the nerves in my back. However, it requires 9V batteries, and rechargeable 9V batteries significantly reduce its power output. Moreover, when using the device at full power, like I do, the batteries need to be replaced every two hours as they become too weak to provide adequate relief.

Frustrated with the limitations of battery-powered devices, I decided to leverage my years of 3D printing experience to create my first 3D model that adapts a 9V wall adapter to a device not designed for wall power. To my delight, the adapter delivers even more power than a fresh battery, and the unit handles it flawlessly. I have rigorously stress-tested the device for several days at 100% power, continuously cycling both channels, and the device remains cool, indicating that this modification is safe for the hardware. Furthermore, this setup eliminates the issue of voltage drop and the need to constantly adjust the knobs during therapy to maintain a consistent power level as the battery weakens.

I am genuinely surprised by how well this modification works. I now use the 9V wall adapter (linked below) in conjunction with my battery blank model and modified battery cover, which provides strain relief for the cable. The adapter I recommend has an exceptionally long cable, allowing you to plug it in almost anywhere without feeling tethered to the wall. Additionally, you can use an extension cord without any issues, as the power draw is minimal, and the adapter remains cool.

It is frustrating that there are no portable TENS devices on the market that accept wall power while delivering the same level of power as the TENS 7000. This device is the only therapy unit I've used that matches the power of professional rigs used in physical therapy and is not merely a cheap gimmick that fails after six months of use. I have been using this device extensively every single day for many years, and it continues to perform reliably. Had I designed this modification earlier, I would have saved hundreds of dollars on 9V batteries, as rechargeable batteries were not providing the power or longevity I required, forcing me to purchase 9V batteries from Costco. As you can imagine, going through one battery every 2-4 hours can become prohibitively expensive.

If you don't already own a TENS 7000 device, I have provided a link to it on Amazon below, along with a link to the AC adapter that my battery blank 3D model is designed to adapt to the unit, incorporating strain relief at the back. The usage of this modification is straightforward: simply place the prongs of the adapter against the prongs in the back of the case, slide the battery blank down over the top of it, and the lip will prevent it from slipping out. The cable is then routed along the channel, exiting through the back, and finally threaded through the new battery case cover. The entire setup can be printed using PLA, as the temperatures involved do not necessitate the use of any other material.

It is my sincere hope that this modification will transform someone else's life as profoundly as it has transformed mine. Living with chronic pain is an immense challenge that can greatly diminish one's quality of life, and any measure we can take to alleviate that pain can make the world seem like a brighter place. If you're on X, feel free to reach out to me at x.com/barnacules, and I'll be happy to answer any questions you may have. This is my first contribution to the site, and I hope that others will find it as beneficial as I have! 👍

Buy 9V AC / DC Adapter
https://amzn.to/3xFgx6j

Buy TENS 7000 Therapy Device
https://amzn.to/3W3UUWE

The battery adapter is 100% my own design, but the cover is modified from the following model to add the hole for the cable to come through so please go show the guy some love! He saved me a little modeling time since he already created a cover. Also, I had lost my cover so I wasn't even going to use one until I saw his model on here, so I went ahead and modified, and it added it. 
https://www.printables.com/model/577484-tens-7000-battery-cover 

Tagi