Purge Station
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
0,37 € – 0,45 € netto (bez VAT)
Dla pliku: Purge Station-PETG.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,41 € netto (środek widełek).
- Masa podana przez autora
- 3 g
- Czas druku podany przez autora
- 31,2 min
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Purge station that removes the need for a purge block!
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 16
- Wydruki
- 0
- Wyświetlenia
- 309
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial
Replace a wasteful purge block that takes up valuable bed space with a purge station! Perfect for reducing waste and speeding up printing time because the printer doesn't have to build up a purge block on layers that have no color changes.
Print in PETG at 0.2 or 0.15 layer hight with 2 perimeters and a 5mm brim for bed adhesion. PLA works too although it may not be as durable.
Required materials:
- Small piece of PTFE tubing
- Small zip tie OR M2 22mm screw and nut
- 2x M4 screws (or 2x M3 screws and 2x washers)
Assembly:
Pass zip tie or M2 screw though the little hole in the side of the printed part and though the PTFE tube and back side of the printed part. Tighten zip tie or screw on M2 nut. Loosely screw the printed part to the back or side wall of your 3D printer. You may need to design and print an additional mounting bracket to join the purge station to your 3D printer frame depending on available screw holes on your specific printer. (See file marked example mounting bracket for inspiration) Insert the M4 screws (or the M3 screws and a washer) into the long screw tracks in the back of the printed part. Make sure the nozzle can reach the center of the purge hole. Slide the printed part upwards until the PTFE tube is touching the side of the extruder nozzle and then completely tighten the screws.
Slicer changes:
NOTE: Use this part and the code at your own risk. The sample below is strictly a guide.
Untick the Wipe Tower option (Print Settings→ Multiple Extruders) in your slicer. Change the Color Change G Code (Printer Settings→ Custom G code → Color Changes G code) to position your nozzle a few millimeters in front of the center of your purge station. Then, move into the center of the purge station, extrude a few mm of filament and return to the position in front of the center of the purge station.
Example:
G1 X200 Y200 ; move to in front of the center of the purge station
G1 Y220 ; move into center of the pruge station
M116 ; wait for temps to be reached
G1 E10 ; extrude 10mm of filament
G4 P1000 ; wait 1 second
G1 X200 Y200 ; move out of the pruge station
