Little Old and Slow Train and Cars
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a model of the trains and cars know as Little Old and Slow
- Ocena
- 5 / 5
- Polubienia
- 18
- Pobrania
- 111
- Wydruki
- 1
- Wyświetlenia
- 699
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Vehicles
- Licencja
- Creative Commons — Attribution
~About~
Lancaster Oxford & Southern Railroad
3D Printed model based on sketches of the L.O.&.S Engine #6 found in the book “Little Old and Slow” the Life and Trials of the Peach Bottom and Lancaster Oxford, and Southern Railroad” By Benjamin F.G Kline Jr.
- The L.O.&.S railroad ran from 1873 to until 1919
- Locals often referred to it as the “Little Old and Slow”
- It was also known as the Peach Bottom Railroad with the nickname of “Ol’ Peachy”
- It was a narrow gauge railroad built on 3’ apart rails (standard gauge is 4’ 8.5”)
- Engine #6 were built in 1905. It was a 22 ton engine by Baldwin Locomotive Works in Philadelphia
- It connected Oxford to the Susquehanna River, where there were ferries
- It connected the Southern end to Oxford and then to Philadelphia as a way to transport cream, cattle, butter, eggs, & poultry to market and transport passengers from the main line Oxford to the ferries on the Susquehanna River
- Stations were at Peach Bottom, Dorsey, Arcadia, Westbrook, Eldora, Gushen, Fulton House, Fairmount, Norwood, Kings Bridge, White Rock, Spruce Grove, Point Lookout, Tweedale, Hopewell, and Oxford
- From about 1905-1917 another line ran from Fairmount to Quarryville with stops at Unicorn, Mechanic Grove, Black Burn, Murray Glen, St. Cathenes, and Quarryville
Tools and Stuff needed- -needle Files -Extra Filament for Pins and Rivets -pliers -Super Glue -Screws (though filament pins and glue can be used)
Here's a few general pointers, if you see a small hole, don't put supports it'll save you time later. also do not put much supports under the bell of the train, it'll take for ever to get out. the amount of supports you will use is up to you, though I used a fair amount. It is designed with screws in mind, though using filament as pins to align the parts and gluing it will work fine. A filament rivet is where you melt and flatten one end with a lighter, then put it on the model and melt then flatten it on the other side.
-Printing Tips
Print the drive linkages with as small layer height as you can, they are small parts and need it.
the rest of the prints can be .15mm layer height or what ever you think best.
use brims if you are afraid of the parts shifting
-Assembly-
~Train wheel plate
You will need to glue the three parts of the wheel plate together, align them as best you can. Once you have that done, you can start on the drive linkage, Start by gluing a pin into the back of the U shaped part (yellow arrows of the second image), then rivet the U shaped part to the short linkage making sure that the thick side is in the U shaped part (red arrow, Second image), then side the pin you glued in into the piston (no need to glue this. then lay the final part of the linkage on and rivet the two together, making sure to go through the train wheel as well. (red arrows, first image)
Then you screw/Glue it to the Train body!


-Coal Trailer
Start by using your lighter to warm up and slightly flatten one end of a piece of filament, then side the crank onto it. then glue the two into the hole on the trailer, leaving a bit of a gap (as shown in the image) then Screw/Glue the trailer wheel plates on, using filament pins to align if you aren't using screws. if you use screws, one will be covered so use a pin there. then add the hitch pin

-Trailer Hitch Pins
Start by melting then slightly flattening one end, sliding into the top hitch (red arrow), gluing it in, then trimming it to length

-Flat Bed Trailer
Start by gluing the flat bed trim onto the flat bed, then Screw/Glue the trailer wheel plates on, using filament pins to align if you aren't using screws. and add the hitch pin
-Box Car
Start by gluing the body to the flat bed, then Screw/Glue the trailer wheel plates on, using filament pins to align if you aren't using screws. and add a hitch pin. then sit the roof on, gluing if needed.
-Small/Large Passenger Car
Start by gluing the frame to the body then Screw/Glue the trailer wheel plates on, using filament pins to align if you aren't using screws and add a hitch pin. then sit the roof on top, gluing if needed
If you need anymore help feel free to ask and I'll try to get back to you as fast as I can!